Teledyne MagnaStar C-2000 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 100

background image

F2. Data Calls Using a CDBR-2 Data Station

1. Connect the Modem or PC’s RJ-11 cord into the Data Station RJ-11

jack. The Data Station must be configured for Modem (either via a
switch or hard wired).

2. Instruct the PC to dial the desired phone number.

NOTE 1: The service indicator (“4” for Modem) should not precede the number.

NOTE 2: If using a PC which will also be used to place fax calls, the Data Station

may be configured for PC (either via a switch or hardwired). In this case,
the service indicator (“4” for Modem) must precede the number.

NOTE 3: Ground-to-Air 4800 bps/9600 bps Modem calls are not currently

supported.

Baud Rate and Link Selection Dialing Prefixes

The following dialing prefix capabilities have been added as part of
software version 4.0A to facilitate the configuration of a specific
data/voice call. These prefixes will override any configurations/factory
default values which were previously programmed.

F3. Baud Rate selection dialing prefixes for individual

modem calls

#4#

Sets baud rate for call at 4800 bps

#9#

Sets baud rate for call at 9600 bps (if both channels
are available)

NOTE: These prefixes override the station default baud rate (See Section VI, B20)

26

(Rev. 8/04)

®

«
...
33
34
35
36
37
...
»

Содержание MagnaStar C-2000





































































































Отзывы:

Нет отзывов

Похожие инструкции для MagnaStar C-2000

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Ultratec Страницы: 28

Бренд: Xblue Networks Страницы: 32

Бренд: Panasonic Страницы: 80

Бренд: PABX Страницы: 27

Бренд: Jabra Страницы: 7

Бренд: Swissvoice Страницы: 103

Бренд: Aastra Страницы: 20

Бренд: MOBICEL Страницы: 69

Бренд: JOIWO Страницы: 6

Бренд: Yada Страницы: 14

Cellular Cradle Plus

Бренд: Wilson Electronics Страницы: 4

Бренд: Curtis Страницы: 6

Бренд: Kenwood Страницы: 42

Бренд: Kenwood Страницы: 38

Basic Telephone and Video Panel 47606-BTV

Бренд: Leviton Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды