Teledyne 340CF ELSD Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 46

Teledyne 340CF ELSD Скачать руководство пользователя страница 35

340CF ELSD

Section 4 Operation

4-7

Load Method Page

If the number selected has no method saved, M

ETHOD

N

OT

A

VAILABLE

will be displayed. If the non-volatile memory IC chip

is damaged, the same message will be displayed.

Note

Method Zero (0) contains a default method for normal and
reverse phase purifications on a Combi

Flash

system when the

ELSD is shipped from the factory. Default method settings are
listed in Section 4.5.

Save Method Page

Up to 8 methods can be saved. Use the

▲

or

▼

keys to select a

method number and the

MENU

|

POWER

key to save the current

conditions to the selected method number. A method includes
Spray Chamber Temperature Setpoint, Drift Tube Temperature
Setpoint, Filter Weight, Calibration Factor, and Detector Gain.

Calibration Page

20% to 100% in 1% increments

Use

▲

or

▼

keys to select an action.

Use 20% with Combi-

Flash

systems.

Push

MENU

|

POWER

key to take an action and go back Home

screen.

Push

AUTOZERO

key to keep the current state and go back Home

screen.

This feature scales the detector output. This feature is useful to
match individual detectors to each other for standardization
within a lab, or set the full scale output to a value other than 5V
or 10mV. At 100%, the signal is neither amplified nor attenuated.

LOAD METHOD:
0 1 2 3 4 5 6 7 8 9

SAVE METHOD:
0 1 2 3 4 5 6 7 8

Calibration:
100%

«
...
33
34
35
36
37
...
»

Содержание 340CF ELSD















































Отзывы:

Нет отзывов