Tekvox TEK 1201-MV Скачать руководство пользователя страница 8

Страница: 8 / 54

www.tekvox.com

1201-MV

79033-MV User Manual

2. Specifications

2.1 Universal Switcher

Video Input

Video Input

(5) HDMI (Type-A, Female)
(1) USB-C (USB Type-C, Female, Powered)

Input Resolution

HDMI (1~4)

: Up to 4K@60Hz 4:4:4

HDMI (5)

: Up to 4K@30Hz 4:4:4

USB-C

: Up to 4K@30Hz 4:4:4

Video Output

Video Output

(1) HDMI (Type-A, Female)
(1) HDBaseT (RJ45)

Output Resolution

HDMI

: Up to 4K@60Hz 4:4:4

HDBaseT

: Up to 4K@60Hz 4:2:0

HDMI Standard

Up to 2.0

HDCP Version

Up to 2.2

Audio Input

Audio Input

(1) AUDIO IN (3.5mm mini jack)
(1) LINE (3-pin terminal block)
(1) MIC (3-pin terminal block)

Frequency Response

20Hz to 20kHz, ±3dB

Max Input Level

2.0Vrms ± 0.1

L-R Level Deviation

< 0.3dB, 1kHz sine at 0dBFS level (or max level before clipping)

Input Impedance

> 10KΩ

AUDIO/LINE/MIC Audio Format

PCM 2.0

HDMI Audio Format

PCM 2.0 48K

L+R Audio Output

Audio Output

(1) L+R Balanced Stereo (5-pin terminal block)

Audio Format

PCM 2.0

Frequency Response

20Hz to 20kHz, ±1dB

Max Output Level

2.0 ± 0.1Vrms

Total Harmonic Dist
Noise (THD+N)

< 0.05%, 20Hz to 20kHz bandwidth, 1kHz sine at 0dBFS level (or
max level)

Signal-to-Noise Ratio (SNR)

> 90dB, 20Hz to 20kHz bandwidth

Crosstalk Isolation

< -70dB, 10kHz sine at 0dBFS level

L-R Level Deviation

< 0.3dB, 1kHz sine at 0dBFS level (or max level before clipping)

Содержание TEK 1201-MV






















































Результаты поиска

Содержание TEK 1201-MV

Отзывы:

Бренды по названию

Популярные бренды

Tekvox TEK 1201-MV, Руководство пользователя

Результаты поиска

Содержание TEK 1201-MV

Отзывы:

Бренды по названию

Популярные бренды