Tektronix TSG4102A Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 99

background image

Installation

Instrument maintenance

Clean your instrument

Clean the exterior surfaces of the chassis with a dry lint-free cloth or a soft-bristle
brush. If any dirt remains, use a cloth or swab dipped in a 75% isopropyl alcohol
solution. Use a swab to clean narrow spaces around controls and connectors. Do
not use abrasive compounds on any part of the instrument because they might
damage the instrument.

CAUTION.

Avoid getting moisture inside the instrument during exterior cleaning;

use just enough moisture to dampen the cloth or swab. Do not wash the
front-panel On/Off button. Cover the button while washing the instrument. Use
only deionized or distilled water when cleaning. Use a 75% isopropyl alcohol
solution as a cleanser and rinse with deionized or distilled water. Do not use
chemical cleaning agents; they might damage the chassis. Avoid chemicals that
contain benzene, toluene, xylene, acetone, or similar solvents.

CAUTION.

To prevent damage to the

fl

at panel display, do not use improper

cleaning agents or methods. Avoid using abrasive cleaners or commercial glass
cleaners to clean the display surface. Avoid spraying liquids directly on the
display surface. Avoid scrubbing the display with excessive force.

Clean the display surface by gently rubbing the display with a clean-room wipe. If
the display is very dirty, moisten the wipe with distilled water or a 75% isopropyl
alcohol solution and gently rub the display surface. Avoid using excess force;
this might damage the display surface.

Upgrade your instrument

Software upgrades are available from Tektronix. They can either be downloaded
from the Tektronix Web site or they can be ordered from your local Tektronix
representative. To add additional software options or features, you will need an
option key from Tektronix. When you receive the software from Tektronix, you
will also receive an option key. Follow the instructions you receive to install the
software on your instrument. You will be prompted to enter the option key. See
the About menu on the instrument to enter an option key. This information is in
the Menus section of this manual. (See page 16,

Return your instrument

If you return your instrument to Tektronix:

When repacking the instrument for shipment, use the original packaging. If
the packaging is unavailable or un

fi

t for use, contact your local Tektronix

representative to obtain new packaging.

Seal the shipping carton with an industrial stapler or strapping tape.

TSG4100A Series RF Signal Generators User Manual

9

«
...
23
24
25
26
27
...
»

Содержание TSG4102A




































































































Отзывы:

Нет отзывов

Похожие инструкции для TSG4102A

HOME NERATOR SYSTEM 18000 WATT

Бренд: GE Страницы: 84

Бренд: Streetwize Страницы: 12

Бренд: RGBlink Страницы: 13

Бренд: ADDER Страницы: 2

Бренд: Helvest Страницы: 2

ATLONA AT-HDVS-RX

Бренд: Panduit Страницы: 2

Бренд: M-system Страницы: 4

Бренд: Audio Nemesis Страницы: 10

Бренд: Nagra Страницы: 18

IFS MC250-4T Series

Бренд: Interlogix Страницы: 23

Бренд: MPP Solar Страницы: 46

Бренд: Microchip Technology Страницы: 28

Бренд: Sonoro Страницы: 40

Бренд: Extron electronics Страницы: 54

Бренд: XTBA Страницы: 3

Бренд: Kisae Страницы: 12

Бренд: Miteq Страницы: 74

Xenus XTL-230-18

Бренд: Copley Controls Corp. Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды