Tektronix TDS 510A, Инструкция по эксплуатации

Страница: 31 / 116

Performance Tests
TDS 510A Performance Verification and Specifications
1–17
Table 1–1: Test Equipment (Cont.)
Item Number and
Description
Purpose Example Minimum Requirements
16. Pulse Generator Tektronix CFG280
(or, optionally, PG 502) Used to Test Video Option 05
Equipped Instruments Only
17. Cable, Coaxial
(two required)
75 , 36 in, male to male BNC
connectors
Tektronix part number
012-1338-00 Used to Test Video Option 05
Equipped Instruments Only
18. Terminator, 75
(two required)
Impedance 75 ; connectors: female
BNC input, male BNC output
Tektronix part number
011-0102-01 Used to Test Video Option 05
Equipped Instruments Only
19. Generator, Sine Wave 100 kHz to at least 400 MHz. Variable
amplitude from 12 mV to 2 V
p-p
.
Frequency accuracy >2.0%
Rohde & Schwarz SMY
3
Checking Analog Bandwidth,
Trigger Sensitivity, Sample-
rate, External Clock, and
Delay-Time Accuracy
20. Meter, Level and Power
Sensor
Frequency range:10 MHz to 400MHz.
Amplitude range: 6 mVp-p to 2 V
p-p
Rohde & Schwarz URV 35,
with NRV-Z8 power sensor
3
Checking Analog Bandwidth
and Trigger Sensitivity
21. Splitter, Power Frequency range: DC to 1 GHz.
Tracking: >2.0% Rohde & Schwarz RVZ
3
Checking Analog Bandwidth
22. Generator, Function Frequency range 5 MHz to 10 MHz.
Square wave transition time
25 ns.
Amplitude range: 0 to 10 V
p-p
into 50
Tektronix CFG280 Checking External Clock
23. Adapter (four required) Male N to female BNC Tektronix 103–0045–00 Checking Analog Bandwidth
24. Adapter Female N to male BNC Tektronix 103–0058–00 Checking Analog Bandwidth
25. Generator,
Leveled Sine Wave,
Medium-Frequency
(optional)
200 kHz to 250 MHz; Variable ampli-
tude from 5 mV to 4 V
p-p
into 50
Tektronix SG 503 Leveled
Sine Wave Generator
1, 3
Checking Trigger Sensitivity
at low frequencies
26. Generator, Leveled Sine
Wave, High-Frequency
(optional)
250 MHz to 1 GHz; Variable ampli-
tude from 500 mV to 4 V
p-p
into 50 ;
6 MHz reference
Tektronix SG 504 Leveled
Sine Wave Generator
1
with
SG 504 Output Head
3
Checking Analog Bandwidth
and Trigger Sensitivity at high
frequencies
1
Requires a TM 500 or TM 5000 Series Power Module Mainframe.
2
Warning: The optional P6243 and P6245 probes that may be used with this oscilloscope provide an extremely low loading
capacitance (<1 pF) to ensure the best possible signal reproduction. These probes should not be used to measure
signals exceeding
±
8 V, or errors in signal measurement will be observed. Above 40 V, damage to the probe may result.
To make measurements beyond
±
8 V, use either the P6139A probe (good to 500 V), or refer to the catalog for a recom-
mended probe.
3
You can replace items 19, 20, or 21 with a Tektronix SG503 (item 25) or SG504 (item 26) – if available.