manualshive.com logo in svg

Tektronix 212, Руководство оператора, Страница: 24 / 35

Поделиться
Скачать
Tektronix 212 Скачать руководство пользователя страница 24

CH 2: Obtain a free-running trace with no signal applied to the

vertical channel input and CH 1 POSition control set to the OFF
detent.  While switching the CH 2 VOL TS/DIV switch between 50 m
and 1 m, adjust the CH 2 STEP ATTEN BAL for minimum trace shift
between adjacent positions.

Horizontal Gain

Set the SEC/DIV switch to X-Y.  Connect the CH 1 probe tip to

an accurate 0.2 volt source (such as a TEKTRONIX 067-0502-01
Standard Amplitude Calibrator).  Set the CH 1 VOL TS/DIV switch to
50 m and the CH 2 POSition control to midrange.  Adjust the HORIZ
GAIN adjustment for exactly four horizontal divisions of deflection
between dots.

Horizontal Timing

Connect the CH 1 probe tip to some accurate timing standard

(such as the TEKTRONIX 2901 Time-Mark Generator).   With the
SEC/DIV   switch   set   to   1   m,   apply   one   millisecond   time   marks.
Adjust the Trigger controls for a stable display.  Adjust the SWP CAL
adjustment   for   exactly   eight   divisions   of   deflection   between   the
second and tenth time mark (one time mark/division).

22

212 Operators Handbook

Содержание 212




































Отзывы:

Нет отзывов