Tektronix 1730 Series, Инструкция по эксплуатации

Страница: 10 / 258

Contents
vi
Figure 3-11: Considerations for custom installation of an instrument. 3–13 . . . . . . . .
Figure 4-1: Simplified representation of the 1730-Series Waveform Monitor. 4–1 . .
Figure 4-2: Simplified block diagram of the Sync Stripper. 4–7 . . . . . . . . . . . . . . . . .
Figure 4-3: Simplified illustration of the Bridge limiter circuit. 4–10 . . . . . . . . . . . . . .
Figure 4-4: Simplified representation of the AFC phase-lock loop. 4–12 . . . . . . . . . . .
Figure 4-5: Elements for line select timing.
Figure 4-6: Relative line select elements for the 2-line display. 4–15 . . . . . . . . . . . . . . .
Figure 4-7: Relative line select timing elements for the 1-line display. 4–16 . . . . . . . . .
Figure 4-8: Timing signals for 1-line and 2-line sweep. 4–17 . . . . . . . . . . . . . . . . . . . . .
Figure 4-9: Z-axis timing for readout. 4–23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4-10: Pinout of the CRT Socket 4–30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 5-1: Remote connector for RGB. 5–5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 5-2: Remote connector for 90/100 triggering. 5–6 . . . . . . . . . . . . . . . . . . . . . . .
Figure 5-3: Ten full cycles of calibrator signal between timing marks. 5–13 . . . . . . . .
Figure 5-4: Equipment hook–up for checking vertical gain. 5–16 . . . . . . . . . . . . . . . . .
Figure 5-5: Checking PIX MON OUT signal amplitude. 5–18 . . . . . . . . . . . . . . . . . . .
Figure 5-6: Initial equipment setup to check flat response. 5–20 . . . . . . . . . . . . . . . . . .
Figure 5-7: Adjustment locations for the Main and Power Supply boards. 5–29 . . . .
Figure 5-8: Segment of the Main board, showing the test points and adjustment
locations for the +11.8 V supplies. 5–31 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 5-9: Equipment setup to adjust 0.2 ms timing. 5–32 . . . . . . . . . . . . . . . . . . . . . .
Figure 5-10: Equipment setup for adjusting the calibrator amplitude. 5–35 . . . . . . . .
Figure 5-11: Equipment setup for adjusting Channel A input compensation. 5–36 . .
Figure 5-12: Adjusting for best flat response. 5–37 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 5-13: Using the high-range multiburst signal to set flatness. 5–39 . . . . . . . . . .
Figure 6-1: Circuit board assembly locations. 6–5 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-2: Multiple pin connectors used in the 1730–Series Waveform Monitor
. 6–6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-3: Bezel removal. 6–17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-4: Rear panel securing screws. 6–19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6-5: Screws that hold the Front Panel circuit board (A2) in place. 6–21 . . . . .
Figure 6-6: Screws holding the Main circuit board (A3) in place. 6–22 . . . . . . . . . . . .
Figure 6-7: Screws holding the Power Supply circuit board (A1) in place. 6–23 . . . . .
Figure 6-8: Repackaging a 1730–Series instrument. 6–24 . . . . . . . . . . . . . . . . . . . . . . .