background image

page 9

3. Unwrap one revolution of hose from 

the reel.

4. Push the air hose through the roller 

guide and reinstall hose stopper.

Keep drum locked at all times.

1. Pull out 2 feet of air hose and lock 

drum. Remove air hose stopper.

2. Pull air hose back through the 

roller guide. 

Keep drum locked at all times.

3. Wrap one revolution of hose onto 

the reel.

4. Push the air hose through the roller 

guide and reinstall hose stopper.

Keep drum locked at all times.

1. Pull out 8 feet of air hose and lock 

drum. Remove air hose stopper.

2. Pull air hose back through the 

roller guide. 

Keep drum locked at all times.

Adjusting Recoil Tension

Hose reel is shipped with spring tension properly set. Be aware that spring tension is calibrated to rewind entire length of air 

hose. If you are working with only a portion of total air hose length or if you feel hose rewinds too quickly or too slowly, you 

can easily adjust the tension of the main recoil spring.

       

DO NOT SET TOO MUCH TENSION IN SPRING. Damage to spring could result.

Decreasing Recoil Tension

Increasing Recoil Tension

U

NWRA

P

FT

FT

W

R

AP

1

2

3

4

1

2

3

4

Содержание 46875













Отзывы: