tekton 46875 Скачать руководство пользователя страница 10

Страница: 10 / 12

ATTACHING INCOMING AIR

For consistent leak-free performance, air inlet is made of solid brass. Brass is a soft metal and extra care should be taken to

avoid cross threading. For a tight, leak-free connection, follow all instructions carefully.
Option 1

Wrap incoming air hose end with thread sealing tape. Thread air hose end into air inlet, taking care not to cross thread.

Tighten connection with wrench. Do not over-tighten.
Option 2

Locate included swivel nut connector. Wrap threaded end with thread sealing tape. Thread into air inlet, taking care not to

cross thread. Tighten connection with wrench. Do not over-tighten. Next, wrap end of incoming air hose with thread sealing

tape. Thread air hose into swivel end of connector, by turning swivel collar. Tighten connection with wrench. Do not

over-tighten.
To ensure optimum performance, check all connections for leaks. With air system pressurized, brush each

connection with soapy water. Inspect closely. Air bubbles indicate leaking air. Tighten any leaking fittings.

OPTION 2

OPTION 1

Lead-in

Hose

Lead-in

Hose

Swivel Nut

Connector

page 10

Содержание 46875












