Tekron NTS 03-G+ Скачать руководство пользователя страница 11

Страница: 11 / 32

TEK-NTS03-G+-Manual-v3.-012022

P a g e

| 11

www.tekron.com

information in this document is provided for informational use only and is subject to change. For further information or support,

go to www.tekron.com.

LCD Alarm

Alarm Name Specification

PwrA

No Power A No power source is detected on power inlet A.

PwrB

No Power B No power source is detected on power inlet B.

Sats

Satellites Low The number of satellites currently being used for time and position

calculations is below the threshold.

Sync

No Sync

The NTS 03-G+ is not synchronized to any source, or the holdover period

has expired, or the timing output inaccuracy has been exceeded.

Hold

Holdover

The NTS 03-G+ has lost sync and is now in holdover.

AntL

No Antenna The antenna circuit current drain is low (typically under 3mA). This could be

caused by:

•

poor connections

•

the connected antenna having a lower current drain specification

•

a component in the antenna system providing power to the antenna

and therefore the time server is not seeing a connected load

•

there being no antenna connected

AntH

Antenna

Short

The antenna circuit current drain is high (typically over 100 mA). This is

caused by a short in the antenna circuit, or by moisture ingress in the

circuit, or if the antenna connected has a higher current drain specification.

N/A*

Antenna

Fault

This alarm is generated if there is high current or low current detected on

the antenna input.

Factory Reset

Cycle Power

Factory Reset

Armed

This alarm is generated if the Forgotten Password Reset (Factory Reset

Process) is enabled and has been initiated by the user.

IRIG

No IRIG-B

Input

No valid IRIG-B source is detected on the NTS 03-G+ input. (This alarm only

appears if the NTS 03-G+ has IRIG-B monitoring enabled).

N/A*

ETHx Link A

Down

This message appears when the NTS 03-G+ has a PRP link enabled on ETH2

with ETH3 and/or ETH5 with ETH6, and there is no link on ETH2/ETH5. This

could be caused by an unplugged cable, or an unpowered network switch

connected to PRP port A.

N/A*

ETHx Link B

Down

This message appears when the NTS 03-G+ has PRP link enabled on ETH2

with ETH3 and/or ETH5 with ETH6, and there is no link on ETH3/ETH6. This

could be caused by an unplugged cable, an unpowered network switch

connected to PRP port B.

N/A*

Overcurrent The time server supports output current monitoring and has detected

excessive current on one or more outputs. Check the I/O tab to identify

which output is experiencing the fault.

Содержание NTS 03-G+
































Результаты поиска

Содержание NTS 03-G+

Отзывы:

Похожие инструкции для NTS 03-G+

Бренды по названию

Популярные бренды

Tekron NTS 03-G+, Руководство пользователя

Результаты поиска

Содержание NTS 03-G+

Отзывы:

Похожие инструкции для NTS 03-G+

Бренды по названию

Популярные бренды