Tekron NTS 03-G+ Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 32

background image

TEK-NTS03-G+-Manual-v3.-012022

P a g e

| 15

www.tekron.com

© 2022 by Tekron International Limited. All Rights Reserved. All trademarks are the property of their respective holders. The

information in this document is provided for informational use only and is subject to change. For further information or support,

go to www.tekron.com.

4.

BACK PANEL – INPUTS AND OUTPUTS

Ant: Antenna Connector (SMA Connector)

The “ANT” antenna input provides an interface for an external active antenna.

The antenna should be connected using a high quality, low-loss 50

Ω coaxial

cable. The center conductor supplies 5 VDC (100 mA max) to power an active

antenna.

Care should be taken to ensure that the connector is not cross threaded when

attaching the antenna lead-in cable. The connector should be tightened firmly by

hand only. Do NOT over-tighten! Ensure the antenna SMA male connector center pin

is straight before plugging in.

Antenna Cable Considerations

The NTS 03-G+ antenna port expects a signal with a gain of at least 15 dB, and no more than 35

dB, with 20 - 35 dB being the optimal gain range.

All antenna cables will introduce some signal loss in the antenna installation system, which will

be dependent on cable length. The total gain of the antenna installation should fall within the

ranges specified below. The total gain is calculated by the gain of the antenna (Tekron supplied

antenna provides 40 dB gain) minus the antenna cable loss.

Figure 16 Recommended antenna cable loss range

Note

: The above figures are based on an average GNSS signal strength of -130 dBm at sea level,

and assumes that the Tekron supplied antenna is used.

«
...
13
14
15
16
17
...
»

Содержание NTS 03-G+

































Отзывы:

Нет отзывов

Похожие инструкции для NTS 03-G+

LUXOMAT net ViSTATION

Бренд: B.E.G. Страницы: 4

Бренд: TYANO Страницы: 68

Бренд: Avaya Страницы: 119

Бренд: Portwell Страницы: 21

Silex Pricom SX-2000U2

Бренд: Silex technology Страницы: 1

Бренд: IBM Страницы: 36

Бренд: Vxl Страницы: 19

PRIMERGY CX400 M6

Бренд: Fujitsu Страницы: 209

PRIMERGY CX272 S1

Бренд: Fujitsu Страницы: 234

Primergy CX270 S2

Бренд: Fujitsu Страницы: 320

Primergy CX270 S2

Бренд: Fujitsu Страницы: 56

Бренд: Kontron Embedded Computers Страницы: 46

Бренд: Huawei Страницы: 39

Бренд: Huawei Страницы: 188

5288 V3 V100R003

Бренд: Huawei Страницы: 297

Бренд: Huawei Страницы: 2

Бренд: QNAP Страницы: 39

Device Installer

Бренд: Lantronix Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды