background image

© 2013 

 400_D - 09/13

16 of 32

Item Field

Range

Access

Description

Set to

ADJUST

-60 to 45°F

(-51.0 to 7.0°C)

Default = 10°F

(-12.0°C)

Installer

OUTDOOR DESIGN 

SECTION B

Typically set to the temperature of the coldest day 
of the year. The outdoor air temperature used in the 
boiler heating curve that is used to determine the boiler 
target temperature. 

EMS2,

EMS1,

4-20

0-10,

2STG,

1STG

Default = 1STG

Installer

BOILER TYPE 

SECTION E

The type of boiler connected to the control.
1STG = single one-stage on-off boiler
2STG = single two-stage on-off boiler
0-10 = 0-10 V (dc) modulating boiler
4-20 = 4-20 mA modulating boiler
EMS1 = tekmar boiler staging controls
EMS2 = Viessmann modulating boilers with 
OpenTherm

VIEW

70 to 200°F

(21.0 to 93.5°C)

Default = 180°F 

(82.0°C)

Installer

BOILER DESIGN 

SECTION B

The supply water temperature required for the boiler 
zones to heat the building on the typical coldest day 
of the year. Recommendations:
High mass radiant floor = 120°F (50°C)
Low mass radiant floor = 140°F (60°C)
Fancoil or air handling unit = 190°F (90°C)
Copper fin-tube convector = 180°F (80°C)
Radiators = 160°F (70°C)
Low profile baseboard = 150°F (65°C)

OFF, 80 to 180°F

(26.5 to 82.0°C)

Default = 140°F 

(60.0°C)

Installer

BOILER MINIMUM 

SECTION B

The minimum allowed boiler target temperature.
Recommendations:
Condensing gas or electric boiler = OFF
Non-condensing gas and oil boilers = 140°F (60°C)

Note:

 If Boiler Type is 0-10 V (dc), 4-20 mA, EMS1 

or EMS2, this setting is defaulted to Off.

ADJUST

sec

10 to 230 seconds

Default = 30 

seconds

Installer

BOILER MOTOR 

SECTION E

The time required for the modulating actuating motor 
to fully open the gas valve or ramp the burner fan 
from off to full speed on a modulating boiler. Set to 
30 seconds unless otherwise recommended by the 
boiler manufacturer.

Note:

 This item is only available when the Boiler 

Type is 0-10 V (dc) or 4-20 mA.

AD

J

U

S

T

 M

E

N

U

Adjust Menu (1 of 3)

The Adjust menu items are the programmable settings used to operate 
the mechanical equipment.

 Continued on next page.

Содержание tN2 house control 400

































Отзывы: