POWER PIPE II™ SYSTEM
Installation
RELEASE DATE
9-13-17
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF TEKA ILLUMINATION AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING
IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF TEKA ILLUMINATION IS STRICTLY FORBIDDEN.
DRAWING
NUMBER
INS-2656-00
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
Finished grade
Pea gravel or sand
Finished grade
Finished grade
Stability Flange
Pea gravel or sand
Finished grade
Pea gravel
or sand
Above Ground
Installation
Pea gravel
or sand
Concrete
Pea gravel
or sand
Pea gravel
or sand
Pea gravel
or sand
Concrete
Below Ground
Installation
Pea gravel
or sand
3. Slide Stability Flange onto Power Pipe II™. Use
Stability Flange to aid in installation of Power
Pipe II™.
2. Excavate trench according to designed lighting
plan. Dig hole a minimum of 24” deep and 10”
wide to accommodate Power Pipe II™ at desired
fixture locations.
1. Determine Soil Type by referencing DIG-IT Guide.
Prep soil according to DIG-IT Guide.
Finished grade
Pea gravel or sand
Finished grade
Finished grade
Stability Flange
Pea gravel or sand
Finished grade
Pea gravel
or sand
Above Ground
Installation
Pea gravel
or sand
Concrete
Pea gravel
or sand
Pea gravel
or sand
Pea gravel
or sand
Concrete
Below Ground
Installation
Pea gravel
or sand
4. Pull low voltage wiring from remote driver to
Power Pipe II™. Allow for additional cable to
make connections to fixture leads and future
service. Place Power Pipe II™ in hole.
Finished grade
Pea gravel or sand
Finished grade
Finished grade
Stability Flange
Pea gravel or sand
Finished grade
Pea gravel
or sand
Above Ground
Installation
Pea gravel
or sand
Concrete
Pea gravel
or sand
Pea gravel
or sand
Pea gravel
or sand
Concrete
Below Ground
Installation
Pea gravel
or sand
5. Back fill with pea gravel or sand prior to pour.
Finished grade
Pea gravel or sand
Finished grade
Finished grade
Stability Flange
Pea gravel or sand
Finished grade
Pea gravel
or sand
Above Ground
Installation
Pea gravel
or sand
Concrete
Pea gravel
or sand
Pea gravel
or sand
Pea gravel
or sand
Concrete
Below Ground
Installation
Pea gravel
or sand
6. Pour concrete (By Others).
Label on Power Pipe II™ indicates
installation depth with finished grade.
7. Make waterproof connections from branch
circuit wiring to integral driver primary
side using waterproof wire connectors.
Connect incoming ground wire to
green fixture wire.
See wiring diagram.
WIRING DIAGRAM
120V
COM
GROUND
WIRING DIAGRAM
Driver
GROUND FROM FIXTURE
120V
+
Fixture
COM
GROUND
Driver
-
GROUND IN T-HOUSING
120V
COM
All line voltage connections must be made
in accordance to NEC standards.
8. Insert wires and connectors into Power Pipe II™.
Place fixture and cap on Power Pipe II™.
9. Tighten three (3) Phillips screws using a Phillips
screwdriver.
DRIVER HOUSING MUST BE INSTALLED ABOVE GRADE. POWER PIPE™ IS LABELED AT GRADE LEVEL.
DRIVER HOUSING INSTALLED BELOW GRADE WILL VOID WARRANTY
Stake Integral Driver Installation
Failure to use waterproof wire connectors
will cause fixture to fail and VOID PRODUCT
WARRANTY.
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.tekaillumination.com • [email protected]