Teka DVL, Инструкция по эксплуатации

Страница: 12 / 42

If your kitchen hood is made of stainless steel,
use proprietary cleaners mentioned in the
product instructions.
✁ ✂ ✄ ☎✆✝ ✞ ✟✠ ✡☛☞ ✌✍ ☞ ✆ ✆✎ ✠ ✏ ✑✒✠ ✍ ✡ ✌✎✓ ✝ ✏✌ ✔ ✝ ✟ ✌✕ ✒ ✞ ✖
water and a neutral soap.
✁ ✗ ✌✘✌ ✞ ✝ ✏✌ ✖ ✌✡✒ ✔ ✔ ✠ ☛ ✏ ☛ ✆ ✝ ✞ ✌✞ ✏ ✓ ✍ ✆✞ ✒ ✙ ✞ ✒ ✏ ✠ ✘✌ ✆ ✞
corrosive products.
✁
✚
✞ ☎ ✡☞ ✌ ✟✠ ✡ ☛☞ ✌ ✍ ☞ ✆ ✆✎ ✝ ✏ ✠ ✍
✛
✒ ☛ ✔ ✆✡ ☞ ✡ ☞ ✒ ✡ ✎ ✆✌✏ ✍ ✆✡
produce fibres.
✁
✚
✆ ✍ ✆ ✡ ✝ ✏✌ ✘ ✒ ✑✆ ✝ ✞ ☛ ✔ ✌ ✒ ✍ ✌ ✞✏
✜
To remove the filters from their fittings, press lightly
on the locks and then pull them off.
The metal filters can be cleaned by soaking them
in hot water with neutral detergent until the fat
dissolves and then rinsing them under the tap
or using special anti-grease products. They can
also be washed in a dishwasher. In this case, it
is advisable to stack them vertically to avoid food
residues to stick to them.
Cleaning in a dishwasher may damage the metallic
✏ ✝ ✞ ✄ ✒ ☛ ✌
✢
✙✔ ✒ ☛✟ ✌ ✍ ✠ ✍
✛
✠ ✡
✣
✓ ✒ ✔ ✡☞ ✆✝
✛
☞ ✡ ☞ ✠ ✏ ✕ ✠ ✔ ✔ ✍ ✆ ✡ ✒ ✄ ✄✌ ☛ ✡
its fat retention capacity.
Once clean, leave them to dry off and then fit them
onto the kitchen hood.
The manufacturer reserves the right to make changes and corrections to its products as it deems
necessary, without altering their basic characteristics.
Problem solving
Proceed with the following checks before calling the Technical Service:
✤✥✦✧★✩ ✥✪✫✬✥✭✫✮ ✯ ✧✮✦✩✬ ✰ ✱✲✳✦✧✭✴✫✮✵
When exterior gas extraction is not possible, then the kitchen hood may be set to purify the air
by recycling it through active charcoal filters.
The active charcoal filters have an active life of between three to six months, depending on
the individual conditions of use. These filters cannot be washed nor regenerated. They must be
replaced once their useful life comes to an end.
GB
Problem Possible cause
Solution
The kitchen hood does not
work.
The mains cable is not
connected to the network.
There is no current in the netw
ork.
Connect the mains cable to the
network.
Provide current to the network.
The kitchen hood does
not extract sufficiently or
vibrates.
Filters are saturated with fat.
Obstruction in the air outlet.
Change or clean the active
charcoal and/or metal filters.
Remove the obstruction.
✤✶✷✸ ✰ ✦✹✩✴✦ ✭ ✯ ✦✪✩ ✥✮✭✥ ✺
During cleaning and maintenance work, make sure
the safety instructions are complied with
.
Cleaning the hood body
Cleaning and maintenance
✻ ✼ ✽✾ ✿❀ ❁ ❀ ❂ ❃ ❄ ❅ ❃ ❆ ❆ ❇ ❈ ✾ ❁ ❁ ❃ ❄ ❆ ❃ ❉ ❊ ✿❂ ❋ ❃ ❄ ● ✿❍
■ ✼ ❏● ❑ ✾ ✿ ❁ ❁ ❀ ❂ ❀ ❃ ✾ ❉ ● ▲ ▼ ▲ ❁ ✿ ❈ ◆ ❖ ❉❂ ✿✿▲ ❄ ▼ P ◗ ❇ ❃ ❉ P ❘ ❇ ❍
❊ ✼ ✽✾ ✿❀ ❁ ❀ ❂ ❃ ❄ ❅ ❃ ❆ ❆ ❇ ❈ ✾ ❁ ❁ ❃ ❄ ❙ ▼ ❙ ▲ ❄ ❍
❚ ✼ ❏● ❑ ✾ ✿ ❁ ❁ ❀ ❂ ❯▲ ❄ ✾ ❁ ❂ ● ▲ ▼ ▲ ❁ ✿ ❈ ◆ ❖ ❉❂ ✿✿▲ ❄ ▼ P ◗ ❇ ❃ ❉ P ❘ ❇ ❍
5) After 3 seconds your settings are saved
automatically.
Cleaning the metal filters
Changing light bulbs
For changing the light bulbs please contact the
manufacturer’s nearest Technical Service.
Filter saturation indicator “F”
When the sign ‘Saturation of the filters’ is on, the filters
should be cleaned.
After cleaning the filters, simultaneously push “+” and
“-” for at least 3 seconds whereupon the sign will be
switched off.