Teka 1199300, Инструкции по установке и рекомендации по использованию и обслуживанию

Страница: 22 / 152

GB
Timing one hotplate
1
The cooking zone to be timed must
be selected. The related decimal
point must be lit up.
2
Select a power level for the hotpla-
te from
1
to
9
using the touch keys
or (12/11).
3
Press clock touch key (6). Timer
indicator (7) will display
00
.
4
Immediately afterwards, enter a
cooking time between
1
and
99
minutes, by using the touch keys
or (12/11). With the former
the value will start at 1, whereas
with the latter it will start at 60. By
pressing both at the same time the
value will be reset to
00
.
When the clock indicator (7) stops flas-
hing, it will start to count down the time
automatically. The indicator (3) relating
to the timed hotplate will alternately
display the selected power level and
the symbol.
When the clock reaches
01
, it will
switch from counting down minutes to
seconds.
Once the selected cooking time has
elapsed, the heating zone being timed
is turned off and the clock emits a series
of beeps for several seconds. The timer
indicator will display a flashing
00
besi-
de the indicator of the hotplate that has
been disconnected.
If you wish to time another hotplate at
the same time, repeat steps 3 and 4.
If the heating zone turned off is hot, its
indicator shows an
H
or otherwise an
0
. To turn off the audible signal touch
any sensor.
Changing the programmed time.
To change the programmed time, you
must press the touch key of the timed
hotplate (4) to select it and then the
clock (6). You may then read and
change the time.
DISCONNECTION OF THE TIMER
If you want to stop the timer before the
programmed time is up.
1
First select the hotplate and then
press clock touch key (6).
2
Use the touch key (11) to redu-
ce the time to
00
. The clock is can-
celled.
For quick switch-off:
repeat step 1 as
above. Simultaneously pressing the
and touch keys (12 and 11) the
timer will be disconnected.
Fondue function
(depending on model)
This function is specially intended for
melting butter, cheese, chocolate, etc.
It uses a power level that is lower than
level
1
. To access the function:
1
Activate the desired hotplate to
power level
1
.
2
Press touch key (11). The
indicator will switch to displaying
the symbol.
To deactivate the function it is sufficient
to press the touch keys or
(12/11), and the indicator will switch to
respectively displaying the lower
power level
0
or the higher one
1
.
Synchro function
(depending on model)
Using this function, it is possible that
two hotplates, identified in the screen
printing, work jointly, both to select a
power level as well as to activate the
timer function.
To activate this function simultane-
ously press the two related selection
touch keys (4). On doing this, the two
decimal points (9) of the hotplates will
light up and they will both be set to
power level 0.
To deactivate this function, again
simultaneously press the two related
selection touch keys (4).
Power Management func-
tion (depending on model)
Some models are equipped with a
power limiting function. This function
allows the total power generated by
the hob to be set to different values
selected by the user. To do this, for the
first minute after having connected the
hob to the power supply, it is possible
to access the power limiting menu.
1
Press the “+” touch key for three
seconds. The letter PL will appear
on the clock (6), if the model
has a timer or on the hotplate indi-
cators (if it is not equipped with
one).
2
Press the locking touch key (8).
The different power values to which
the hob can be limited will appear
and these can be changed using
the “+” and “-” touch keys.
3
Once the value has been selected,
once again press the locking touch
key (8). The hob will be limited
to the chosen power value.
If you want to change the value again,
you must unplug the hob and plug it in
again after a few seconds. Thus you
will again be able to enter the power
limiting menu.
Every time the power level of a hotpla-
te is changed, the power limiter will
calculate the total power the hob is
generating. If you have reached the
total power limit, the touch control will
not allow you to increase the power
level of that hotplate. The hob will beep
and the power indicator (3) will blink at
the level that cannot be exceeded. If
you wish to exceed that value, you
must lower the power of the other hot-
plates. Sometimes it will not be
enough to lower another by a single
level as this depends on the power of
each hotplate and the level it is set at.
It is possible that to raise the level of a
large hotplate that of several smaller
ones must be turned down.
If you use the quick switch-on at maxi-
mum power function and the said
value is above the value set by the
limit, the hotplate will be set to the
maximum possible level. The hob will
beep and the said power value will
blink twice on the indicator (3).
Safety switch off function
If due to an error one or several hea-
ting zones do not switch off, the
appliance will be automatically discon-
nected after a set amount of time (see
table 1).
22