TECNARE EXEL ACOUSTICS SL ARRAY Series Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 52

TECNARE EXEL ACOUSTICS SL ARRAY Series Скачать руководство пользователя страница 31

Rigging Assembly Guide

30

4

Groundstacking with the THV21-18VR Grid

A CLa21 array must be stacked onto an THV21-18VR grid. The grid increases the array

stability.

With some restrictions, the THV21-18VR grid safely groundstacks up to:

A grid stacked array can be composed of a maximum of 8 CLa21 enclosures along with
all loudspeakers cables.

A ground stacked array requires to be installed on a perfectly horizontal and regular
surface. It can be composed of a maximum of 4 SW-18VR / 8 CLa21 or 8 SW-18VR
enclosures along with all loudspeakers cables.

CAUTION: Potential risk of personal injury and damage to equipment. Groundstacks with
extreme splay angles that locate the stack's center of gravity outside the grid (for

example, eight CLa21, each with 13- degree splay angles) are not supported.

Fig.25 THV21-18VR with groundstacked CLa21s

The loudspeaker at the bottom of the groundstack is secured to the grid’s four captive

guide links arms (two per side) with the quick-release pins included with the loudspeaker.

«
...
29
30
31
32
33
...
»

Содержание EXEL ACOUSTICS SL ARRAY Series





















































Отзывы:

Нет отзывов