TECNARE EXEL ACOUSTICS SL ARRAY Series Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 52

TECNARE EXEL ACOUSTICS SL ARRAY Series Скачать руководство пользователя страница 19

Rigging Assembly Guide

18

When the front links guide are attached at +4 degrees, the pins must be inserted in the

holes which the splay angles are labeled in brackets.

The splay angles listed on the guide link labels are for relative angles between the center
axes  of  the  linked  units.  For  example,  setting  the  guide  links  to  5  degrees  yields  a  5-
degree  downtilt  of  the  lower  unit  to  the  upper  unit.  How  the  loudspeakers  relate  to  the
floor, stage, and seating angles in the venue  depends on the orientation of the grid, the
angles  of  the  loudspeakers  in  the  array  above  them,  and  other  factors.  EASE  Focus
prediction  software  should  be  used  to  calculate  optimum  splay  angles  for  loudspeakers
and to predict coverage patterns for arrays.

CAUTION: CLa21 guide links arms must be secured with the included quick-release

magnets pins. At not time should the weight of the enclosure rest on the knobs when the link
are fully extended (without the pins inserted). The purpose of Knobs of guide links arms is only
extend and retract the guide links arms.

CLA21 SPLAY ANGLES FOR TOP FLOWN CABINETS

When flying CLa21 below THV21-18VR grid, splay angles of -6 to 7 are possible for top

cabinet with the following guide links arms configurations.

The holes which the splay angles are labeled in brackets.

When flying CLa21s from the THV21-18VR It is recommended to select the 6º angle on
the Cla21 intended to be linked to the THV21-18VR. In this way the Cla21 axis will be
parallel to the THV21-18VR

CAUTION:

To link the THV21-18VR and Cla21 the quick-release pin-lock must always be

done by placing it on the rear guide arm in stack mode (fixed) position.

REAR GUIDE LINK TO

FRONT GUIDE LINK TO

RESULTING ANGLE

0

0

-6

0.5

0

-5.5

1

0

-5

2

0

-4

3

0

-3

4

0

-2

5

0

-1

6

0

0

7

0

1

8

0

2

4(9)

+4

3

5(10)

+4

4

6(11)

+4

5

7(12)

+4

6

8(13)

+4

7

«
...
17
18
19
20
21
...
»

Содержание EXEL ACOUSTICS SL ARRAY Series





















































Отзывы:

Нет отзывов