TECNA 2P2B00 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 36

TECNA 2P2B00 Скачать руководство пользователя страница 24

PROVASET 2P code 2P2B00 - 2P6B00 - Instruction manual

rev. 14/02/2013

page 24

Parameter

ENABLE FOR TEST OBSTRUCTION

NO

: Obstruction test disabled

YES

: Obstruction test enabled

Parameter

FINAL PRESSURE DISCHARGE

You are asked to enable or not the automatic air discharge in the tested piece at the test
end.

NO

: Pressure discharge disabled: the tested part remains under pressure at end of test;

YES

:

Pressure discharge enabled: at the end of test the valves are automatically opened
to drain to discharge the pressure inside the tested part;

Only for

2P2B00

model

MAN:

Manual pressure discharge:

–

the pressure is discharged inside the tested part only when the operator
disconnects the part from the equipment;

–

if the test was passed, the green light turns off and the display changes to the
message indicating ready for a new start with the selected test table.

Parameter

BUZZER

xx

: Duration of the sound signal at the test end in case of error or failed result.

Range 0

÷

99 seconds.

Parameters

PROGRAMMING

NO

: Programming disabled

YES

: Programming enabled

«
...
22
23
24
25
26
...
»

Содержание 2P2B00





































Отзывы:

Нет отзывов