TechWind SDK-500 Скачать руководство пользователя страница 2

User's manual for 

elevator door controller 

SDK-500

Copyright

Copyright © 2007,TechWind. All rights reserved.

This document may not be copied or otherwise reproduced, in whole or in part, except
as specifically permitted under international copyright law, without the prior
written consent from TechWind.

Disclaimer

THE INFORMATION IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. 
TechWind  ASSUMES NO RESPONSIBILITY FOR INACCURACIES OR OMISSIONS AND 
SPECIFICALLY   DISCLAIMS   ANY   LIABILITIES,   LOSSES,   OR   RISKS,   PERSONAL   OR 
OTHERWISE, INCURRED AS A CONSEQUENCE, DIRECTLY OR INDIRECTLY, OF THE 
USE OR APPLICATION OF ANY OF THE CONTENTS OF THIS DOCUMENT. FOR THE  
LATEST   DOCUMENTATION,   CONTACT   YOUR   LOCAL   SUPPLIER   OR  TechWind 
COMPANY.

This   publication   may   contain   examples   of   screen   captures   and   reports   used   in   daily 
operations.   Examples   may   include   fictitious   names   of   individuals   and   companies.   Any 
similarity to names and addresses of actual businesses or persons is entirely coincidental. 

Trademarks and 

patents

TechWind name and logo are registered trademarks of TechWind company.
SDK-500 product and logo are registered trademarks of TechWind company.
Other trade names used in this document may be trademarks or registered trademarks of the 
manufacturers or vendors of the respective products.

Software license

agreement

Software and firmware supplied with products is proprietary and furnished under license and 
can be used or copied only in accordance with the license terms.

THE   ENCLOSED   PROGRAM   IS   FURNISHED   SUBJECT   TO   THE   TERMS   AND 
CONDITIONS OF THIS AGREEMENT. RETENTION OF THE PROGRAM FOR MORE THAN 
30   DAYS,   OPENING   OF   THE   SEALED   WRAPPER,   IF   ANY,   SURROUNDING   THE 
PROGRAM,   OR   USE   OF   THE   PROGRAM   IN   ANY   MANNER   WILL   BE   CONSIDERED 
ACCEPTANCE   OF   THE   AGREEMENT   TERMS.   IF   THESE   TERMS   ARE   NOT 
ACCEPTABLE,   RETURN   THE   UNUSED   PROGRAM   AND   ANY   ACCOMPANYING 
DOCUMENTATION TO  TechWind FOR A FULL REFUND OF THE LICENSE FEE PAID.

Intended use

Use this product only for the purpose it was designed for; refer to the data sheet and   user 
documentation. For the latest product information, contact your local supplier or visit us onlin e 
at www.

 

 techwind

 

 .pl

   

European directives

The   European   directive   “Waste   Electrical   and   Electronic   Equipment” 
(WEEE)   aims   to   minimise   the   impact   of   electrical   and   electronic 
equipment waste on the environment and human health. To conform with 
this directive, electrical equipment marked with this symbol must not be 
disposed   of  in   European   public   disposal   systems.   European   users   of 
electrical equipment must now return end-of-life equipment for disposal. 
Further   information  can   be   found   on   the   following   website: 
www.recyclethis.info.

2

Содержание SDK-500





































Отзывы: