TechVision PS8E1N2 Скачать руководство пользователя

Страница: 75 / 121

Alarm Management

DVR User Manual

delay time of the buzzer, please see 9.5.4 Buzzer for details.

Pop-up Video

: After camera setting, the system will pop up the corresponding video

automatically when the sensor alarm is triggered. To set the duration time of the video, please
see 9.5.3 Display for details.

Pop-up Message Box

: if enabled, the system will pop up the corresponding alarm message box

automatically when the sensor alarm is triggered. To set the duration time of the message box,
please see 9.5.3 Display for details.

E-mail

if enabled, the system will send an e-mail when the sensor alarm is triggered. Before

you enable the email, please configure the recipient’s e-mail address first (see 11.1.5 E-mail
Configuration for details).

9.2 Motion Alarm

Motion Alarm

: when the motion object appears in the specified area, it will trigger the alarm.

You should enable the motion of each camera first and then set the alarm handling of the
camera to complete the whole configuration of the motion alarm.

9.2.1 Motion Configuration

①

Click Start



Settings



Camera



Motion to go to the following interface.

②

Select the camera, enable the motion and set the sensitivity and duration of the camera.

Sensitivity

: the higher the value is, the more sensitive it is to motion. You should adjust the

value according to the practical conditions since the sensitivity is influenced by color and time
(day or night).

Duration

: it refers to the interval time between the adjacent motion detections. For instance, if

Содержание PS8E1N2


























































































































Результаты поиска

Содержание PS8E1N2

Отзывы:

Похожие инструкции для PS8E1N2

Бренды по названию

Популярные бренды

TechVision PS8E1N2, Руководство пользователя

Результаты поиска

Содержание PS8E1N2

Отзывы:

Похожие инструкции для PS8E1N2

Бренды по названию

Популярные бренды