TechVision PS8E1N2 Скачать руководство пользователя

Страница: 100 / 121

Device Management

DVR User Manual

11.1.9

Platform Access

Some models may not support this function.
This function is mainly used for connecting ECMS/NVMS. The setting steps are as follows.
Click Start



Settings



Network



Platform Access to go to the interface.

Platform Access

①

Set “Access Type” as “Platform Software” and select “Enable” as shown below.

②

Check the IP address and port of the transfer media server in the ECMS/NVMS. The

default server port for auto report is 2009. If it is modified, please go to the transfer media
interface to check.

③

Enable the auto report in the ECMS when adding a new device. Then self-define device

ID and input the remaining information of the device in the ECMS/NVMS.

④

Input the above-mentioned server address, port and report ID in the server interface. Then

click the “Apply” button to save the settings. Now the ECMS/NVMS system will
automatically connect this device.

11.1.10

SNMP

①

Click Start



Settings



Network



SNMP to go to the interface for SNMP configuration.

Содержание PS8E1N2


























































































































Результаты поиска

Содержание PS8E1N2

Отзывы:

Похожие инструкции для PS8E1N2

Бренды по названию

Популярные бренды

TechVision PS8E1N2, Руководство пользователя

Результаты поиска

Содержание PS8E1N2

Отзывы:

Похожие инструкции для PS8E1N2

Бренды по названию

Популярные бренды