TechnipFMC Smith Meter C2 Скачать руководство пользователя страница 17

Страница: 17 / 30

Issue/Rev. 0.6 (12/18) ║ MN01005 • Page 17

2-Bladed Double Case PD Meters Service Manual

Clearance Checks

3 – Clearance Checks

3.1.

Clearance Guide

This clearance guide lists the recommended minimum and maximum fitting clearance for repaired

meters. (All units of measurement are inches).
Meters often exhibit acceptable accuracy even if the clearances exceed the ranges shown.

The above clearances apply to meters operating at standard operating temperatures and viscosity

range as listed below. For meters built to operate at higher temperature and viscosity (designated

by a 6-digit serial number). Consult factory. Specify serial number and record special clearances

in space provided.

Standard Temperature Ranges

C2 Through G6:

-20°F (-29°C) to 150°F (65°C)

H8:

-20°F (-29°C) to 137°F (58°C)

JA10:

-20°F (-29°C) to 125°F (52°C)

Standard Viscosity Limit

C2 Through H8:

Less than 2,000 SSU (400 mPa•s)

JA10:

Less than 1,000 SSU (200 mPa•s)

3.2.

Clearance Checks

Clearances should be checked with a leaf type feeler gauge and compared with the Clearance

Guide Table.
Any average of clearances that are outside of the tolerance listed should be noted. Certain parts

may be at or over the maximum shown but consideration should be given to the condition of the

part and the accuracy obtained during meter calibration. Certain major parts such as the rotor,

cam, and blades need not be replaced if the meter proving records show no appreciable change

in accuracy between provings.

Meter

Model

(B) Rotor to

Block

Clearance

(F) Rotor

Adjustment

Total End

Clearance

(C) Blade Slot

Clearance

(D) Blade Ends

Below

Rotor

Clearance

(E) Blade Roller

Over Cam

Radius

Clearance

(A) Blade Tip

to Housing

Clearance

.002"-.004"

.005"-.009"

.001"-.004"

.000"-.003"

.001"-.005"

.003"-.005"

E3, E4

.002"-.004"

.005"-.011"

.001"-.005"

.000"-.004"

.001"-.005"

.003"-.005"

.003"-.006"

.005"-.011"

.002"-.005"

.000"-.004"

.001"-.005"

.004"-.006"

.003"-.006"

.007"-.013"

.002"-.005"

.000"-.004"

.001"-.005"

.006"-.008"

.004"-.007"

.010"-.016"

.002"-.006"

.000"-.004"

.001"-.006"

.007"-.011"

JA10

.004"-.008"

.010"-.016"

.002"-.006"

.000"-.004"

.001"-.006"

.008"-.013"

NOTE: For Special Clearances, Consult Factory or Authorized Service Representative.

Table 3

Содержание Smith Meter C2































Результаты поиска

Содержание Smith Meter C2

Отзывы:

Похожие инструкции для Smith Meter C2

Бренды по названию

Популярные бренды

TechnipFMC Smith Meter C2, Руководство по обслуживанию

Результаты поиска

Содержание Smith Meter C2

Отзывы:

Похожие инструкции для Smith Meter C2

Бренды по названию

Популярные бренды