TEC B-450 SERIES, Руководство пользователя

Страница: 154 / 222

6-4
EO18-33003A 6. DIAG. TEST OPERATION
Count Condition
Counted when the feed motor drives to feed, print
and issue the paper. (Counted also during back
feed.) [See NOTE 2].
Counted while printing. (Feeding and issuing
paper, are not counted.) [See NOTE 2.]
Counts every cut. [See NOTE 3.]
Counted when the Ribbon motor is driven to feed,
print, etc. [See NOTE 4.]
Counted when a parity, overrun or framing error
occurs. [See NOTE5.]
Counted when a zero-dividing error occurs or
undefined command is retrieved.
Counted when a momentary power failure occurs.
Fig. 6-1
(Revision Date: Jan. 22, 2001)
6.2 SELF TEST MODE
■
Sample Print A
[Print Condition]
•
Preset count : 1
•
Print speed : 2”/sec.
•
Sensor : No sensor
•
Supply length : 76 mm (TS model)
105 mm (HS model)
•
Issuing mode : Batch printing
1) Maintenance Counter
#
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
Item
Total paper distance
covered
Paper distance
covered
Print distance
Cut count
Ribbon motor drive
time
RS-232C hardware
error count
System error count
Momentary power
failure count
Range
0.0 to 3200.0 km
0.0 to 200.0 km
0.0 to 200.0 km
0 to 1000000 times
0 to 2000 hours
0 to 255 hours
0 to 15 times
0 to 15 times
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(15)
(16)
(17)
(18)
(33)
(35)
TL FEED 0.0km
FEED 0.0km
PRINT 0.0km
CUT 64
RIBBON 0h
232C ERR 255
SYS ERR 0
PW FAIL 0
PRINT SPEED CUT +0.0mm
[PC] +1.0% BACK +0.0mm
[KEY] +0.0% TONE (T) +0.0mm
X ADJ. +0.0mm TONE (D) +0step
RIBN ADJ. [PC] +0 +0 [KEY] +0 +0
FONT [PC1254] [0] [¥]
SPEED [9600] PARITY [EVEN]
CONTROL [XON/XOFF]
CODE [AUTO] STATUS [OFF]
THRESHOLD R 1.0V T 0.7V
KANJI [TYPE1] EURO CODE FFH
STACKER [OFF] TT BLOCK [13]
GAIJI BLK [15] PCSAV BLK [0]
RBN TYP [00]
[PC]
FEED
+0.0mm
CUT +0.0mm
BACK +0.0mm
TONE (T) +0step
TONE (D) +0step
[KEY]
FEED
+0.0mm
(19)
(20)
(21)
(22)
(23)
(24)
(25)
(26)
(27)
(28)
(29)
(30)
(31)
(32)
(34)
NOTES: 1. Item from (2) through (8) are initialized to “0” after RAM clear.
2. If the distance is 8.2 m or less (TS model)/4.1 m (HS model) or less, it is rounded down
and no data is added to the memory at power off. If the distance is less than 0.5 km,
“0.0 km” is printed.
3. If the count is 31 counts or less, it is rounded down and no data is added to the memory
at power off.
4. If the driving time is 32 sec. or less, it is rounded down and no data is added to the
memory at power off.
5. When a sent command results in an error, the same number as the data capacity of
the command is counted by byte.