9
TEC-61201-1
Technical Manualе
PRIZRAK-510, 520 v7
User Settings Configuration
Menu 2. User settings
No. Type
Factory
default
settings
Number of audible signals
1 Immobilizer
On
1 – ON
2 – OFF
2 AntiHiJack
3 AntiHiJack response delay
1
Range 1 to 10 1 – 100 m; ...10 – 1000 m. Sets the
distance until the engine lock
4
Audio confirmation of authentication by PIN-code
On
1 – ON
2 – OFF
5
Automatic deactivation of Maintenance mode
6 Activation of Central Lock while driving
Off
7 Deactivation of Central Lock after ignition is turned off
8 Automatic window roll up (Comfort feature)
On
Programming sequence
1.
Turn the ignition on.
2.
Enter PIN code, wait for confirmation.
3.
Once the system has been powered, within 10 seconds enter
the configuration menu by pressing the Programming button
12 times. If your actions are correct, the Immobilizer will
confirm it by 4 audible signals.
4.
Select the option from the menu by pressing the Programming
button a required number of times (equal to the number of the
option). The Immobilizer will acknowledge the option number
by a series of audible signals.
5.
Go to option setting by pressing and holding the brake pedal.
The Immobilizer will notify of the option status by a series of
audible signals of a changing duration.
6.
Adjust option settings by pressing the Programming button
the number of times matching the number of steps from the
current status to the required one. Please remember that from
the last function the program will go to the first one.
7.
Release the brake pedal. Now you can move to programming
the next function or exit the programming mode.
8.
Go to configuring another option by pressing the Programming
button the number of times matching the number of steps
from the current option to the required one. For example, to
go from option 2 (AntiHiJack) to option 6 (Activation of Central
Lock while driving) press the Programming button 4 times.
You can exit programming mode at any moment by turning off
the ignition. A trill will sound. If no actions were taken within
60 seconds and brake pedal was released, the Immobilizer will
exit programming mode.
You can exit programming mode at any moment by turning off the
ignition. A trill will sound. If no actions were taken within 60 seconds
and brake pedal was released, the Immobilizer will exit programming
mode.
•
If the vehicle has travelled 10 km after installation, and
factory default PIN code remained unchanged, it is
allowed to use PIN code “2” for identity verification by
pressing an integrated button.
•
To change method of authentication (option 9) you must
enter PUK-code: you can find it under the opaque cover
on the plastic card. No audible signals are generated
before entering the PUK-code. Afterwards a trill will
sound, and the system will indicate the option number.
•
PUK-code as a means for changing the authentication
method is not required if:
1.
the vehicle travelled less than 10 km after installation
of the Immobilizer (Speed Control is available).
2.
the ignition was not active for more than 20 minutes
after installation of the Immobilizer (Speed Control
is not available)
Changing PIN code
1.
Turn the ignition on.
2.
Enter PIN code, wait for confirmation.
3.
Press the Programming button 10 times within 14 seconds
after the authentication. Wait for confirmation by 1 audible
signal.
4.
Set the new PIN code by using any combination of buttons.
Now you can use the buttons. Pressing is confirmed by an
audible signal.
5.
Wait for confirmation by 1 audible signal.
6.
Re-enter the new PIN code.
7.
Wait for confirmation:
•
2 audible signals and a sound trill mean that the PIN code
has been changed and the Immobilizer has left the PIN
code changing mode.
•
Sound alert means that the PIN code has not been changed:
An error occurred while entering a new PIN. Repeat PIN
changing procedure starting from step 4.
You can exit the PIN code changing mode anytime by turning the
ignition off.
•
You cannot change PIN to «1» – a single push of a button.
Reassigning Programming Button
1.
Reset all settings to factory default.
2.
Run the Immobilizer interfacing procedure.
3.
If analog steering wheel buttons are used please define them
(see above for the description of this procedure).
4.
In order to assign any of the buttons recognized by the
Immobilizer as the Programming button, press the selected
button and hold it for at least 5 seconds until a long audible
signal is heard.
The Programming button can be assigned within 15 minutes after
the Immobilizer interfacing with the vehicle.
