6
◊
Assign the Programming button from available ones
by pressing and holding it for no less than 5 seconds
(until an audible signal will be heard).
Programming stage two. Immobilizer configuration pro
-
gramming
At stage two Immobilizer hardware functions and user settings
are changed and a new PIN code is programmed. Three independent
menus are used during programming (see Programming menu table).
Table 2. Programming menu
Name
Menu entering
code
Audible signals
number
Function
Menu 1
10
3
Immobilizer hardware settings configuration (see page 6)
Menu 2
12
4
Immobilizer user settings configuration (see page 8)
Menu 3
14
1
PIN code changing (see page 9)
Immobilizer hardware features programming (Menu 1)
Programming is carried out in accordance with Immobilizer hardware features programming (Menu 1) table.
Table 3. Hardware features programming (Menu 1)
No.
Option name
Setting range
Factory de-
fault settings
Notes
1
Vehicle model
-
-
–
2
Changes locking
1 – 4
2
1 - Public, 2 - OFF, 3 - User, 4 - Admin
3
Engine locking
1 – 3
2
1- normally open relay control
2- normally closed relay control
3- reserved by manufacturer
4
Safe locking mode
1 – 2
2
1-Safe locking mode on
2- Safe locking mode off
5
External buttons type
1 – 2
1
1- Outputs No. 10 and 11 are used as analog buttons
2- Output No. 10 and 11 are used as digital buttons
6
Hazard lights control algo-
rithm
1 – 6
-
1- impulse negative control
2- status negative control
3- impulse positive control
4- status positive control
5- lamps control
7
(-) Output No. 3
1 – 20
2
Programmable negative output (Arming impulse by default)
8
(-) Output No. 4
1 – 20
20
Programmable negative output (PIN code entering impulse by de-
fault)
Annotations to Table 3
p. 1. Vehicle model allows forced selection of vehicle group and sub
-
group.
p. 2. Change locking allows prohibiting the Immobilizer hardware
features reprogramming.
This point has 4 conditi
ons:
1 Public –
reprogramming prohibition is set for all menu options
except for 2;
2 O F F –
p r o h i b i t i o n i s r e m o v e d a n d a l l o p t i o n s
can be reprogrammed;
3 User –
prohibition is set for all the options aside from 1. Pass
-
word needs to be entered in order to remove prohibition (see
below);
4 Admin –
prohibition is set for all menu options. Password needs
to be entered in order to remove prohibition.
Settings 1 (Public) and 2 (OFF) can be set with Programming button.
Settings 3 (User) and 4 (admin) and the password can be set only
while programming the Immobilizer with a PC or TECPROG original
programming unit. User or Admin prohibition can be removed only
with TECPROG upon entering the password. You can go from User
mode to Public mode in order to prohibit the reprogramming of all the
options except for 2. In this case you can go only back from Public
mode to User mode.
Resetting to factory default settings leads to resetting of only the op-
tions, reprogramming of which has not been password protected.
In any condition of option No. 2 you can access the menu, navigate
all the options and check every option’s condition.
p. 3. Engine locking allows setting the output No. 2 for normally
open relay.
p. 4. Safe locking mode. With this mode on, Engine locking will be ac-
tivated only if the vehicle speed is 30 km/h or less.
p. 5. External buttons type. Depending on the buttons used:
◊ Inputs No. 10, 11 are used for connecting analog (steer
-
ing wheel) buttons
◊ Inputs No. 10, 11 are used for connecting digital (posi
-
tive/negative) buttons
p. 6. Hazard lights control algorithm allows setting the required con-
trol algorithm. In the majority of cases the algorithm is set automatically
during vehicle interfacing.
p. 7. (-) Output No. 3 is a programmable negative output (Arming
impulse by default).
p. 8. (-) Output No. 4 is a programmable negative output (PIN code
entering impulse by default).
Programming sequence
1 Turn the ignition on.
2
Enter the PIN code and wait for confirmation.
3
Enter Menu 1 by pressing and releasing the Programming button
10 times (you need to do this no later than 10 seconds upon
PIN code entering). The Immobilizer will notify of menu accessed
by three sound trills.
4 Select menu option by pressing and releasing the Programming
button for the number of times corresponding with the menu
option number. The Immobilizer will inform on menu number
by series of audible signals.
5 Go to option setting by pressing and holding the brake pedal.
The Immobilizer will inform you on the option setting by series
of audible signals, and their duration will change.
