3
Available PIN code options
,
,
,
,
- buttons are used as an example. Please refer to the Integrator software files for the list of buttons perceived by the unit.
Single-button PIN code entering
One-digit PIN code:
Two-digit PIN code:
~2 second pause
Multiple buttons PIN code entering
When entering the PIN code you need to keep in mind the button pressing sequence.
One-digit PIN code:
Two-digit PIN code:
~2 second pause
Immobilizer feature
Immobilizer feature is designed for preventing the vehicle from being
stolen from its parking area. Immobilizer enters the Guard mode when
the ignition is turned off for longer than 30 seconds. If the Immobi-
lizer feature is in Guard mode then it is necessary to enter the correct
PIN code otherwise the engine will be locked:
◊ The engine will be turned off right after the vehicle
starts moving if the Speed control is on and is supported
by the vehicle.
◊ The engine will be turned off within 5 seconds after
the ignition has been turned on if the Speed control
is off or is not supported by the vehicle.
Immobilizer can leave the Guard mode and the engine lock can be un-
locked by entering the PIN code without turning the ignition off prior
to the procedure.
You do not need to enter the PIN code again if the ignition has been
off for less than 30 seconds.
Anti HiJack feature
Anti HiJack is the function that prevents the vehicle from being
hijacked or stolen from its parking area.
Anti HiJack enters the Guard mode in the following cases:
◊ The ignition has been turned off for longer than 30 seconds
(in case if Immobilizer feature was not on; if it was on then
the Immobilizer will follow its algorithms).
◊ Driver’s door has been opened.
Upon entering the Guard mode, Anti HiJack feature passes a sequence
of phases and in case if the Guard mode has not been deactivated,
the feature will activate the Engine locking.
Changing of phases takes place only when the ignition is on. When
ignition has been turned off the Immobilizer will save its current condition
and will continue its operation when the ignition is back on.
Anti HiJack’s Guard mode can be deactivated at any phase by enter
-
ing the PIN code.
Guard mode includes the following phases:
◊
Idle phase
◊
Alarm phase
◊
Locking phase
Idle phase
In this phase Anti HiJack follows two different algorithms depending
on the availability of Speed control.
If the Speed control is available, Anti HiJack waits until the vehicle
covers a set distance from the moment of Guard mode activation. Upon
that, Anti HiJack goes into the Alarm phase.
If the Speed control is not available, Idle phase consists of three stages:
◊ Waiting for driver’s door closing
◊
Waiting for a certain number of brake pedal pressings
◊
Pause before Alarm phase initiation
Alarm phase.
This phase consists of two stages:
◊
Driver warning on the necessity of entering the PIN code
(10 seconds). It is carried out by an audible sound alert.
◊
Warning the other drivers on the road on the possible
hazardous situation due to the upcoming engine locking
(10 seconds). It is carried out by vehicle hazard lights
warning the other drivers.
If at any of the stages mentioned above attempts of entering the PIN
code shall occur, the stage’s duration may be increased up to 20 sec
-
onds, but the overall phase duration cannot be longer than 30 seconds.
Locking phase.
Engine locking is activated. Hazard lights will be on for 15 seconds.
Anti HiJack will be in the locking phase until the PIN code is entered.
When safe locking mode is on (see Immobilizer hardware
settings programming (Menu 1) section), Engine locking will
be activated only if the vehicle’s speed is 30 km/h or less.
If the vehicle speed exceeds 30 km/h the Immobilizer will wait
for speed decrease for an unlimited amount of time (while
the vehicle is moving). As soon as the speed goes as low as
30 km/h the immobilizer will lock the engine
Use of safe locking mode allows mitigating the risk of collisions when
Engine locking is activated.
When the ignition is off Anti HiJack turns the hazard lights and au-
dible driver warning signals off. If the Immobilizer feature has not
entered the Guard mode (see the Immobilizer feature section) then,
upon the next ignition activation Anti HiJack will activate audible driver
warning and hazard lights for 15 seconds. In the meantime Anti HiJack
feature allows starting the engine but will prevent driving following
the same algorithms as Immobilizer feature.
If the Immobilizer feature has entered the Guard mode, then, upon
ignition’s deactivation Anti HiJack feature will stop its operation and Im
-
mobilizer will follow the algorithms of Immobilizer feature.
Maintenance mode
Maintenance mode is an operation mode when all theft prevention
and service functions of Immobilizer are temporarily deactivated.
With Maintenance Mode on, entering the PIN code is not needed when
driving the vehicle, which is helpful when the car needs to be put for
maintenance in the service center. Still, in order to enter the Program-
ming mode, it is necessary to enter the PIN code.
When the ignition is turned on in Maintenance mode, a long audible
tone is sounded that reminds on the fact that the Immobilizer is in
maintenance mode. The audible tone can be turned off for secrecy
level increase.
In order to activate or deactivate the Maintenance mode you need
to do the following:
1 Turn the ignition on Enter the PIN code and wait for confirmation
2 Press and release the Programming mode button 6 times (start
doing it no later than 10 seconds after PIN code entering).Please
wait for confirmation that you have successfully performed
the actions:
◊ 1 audible signal and 1 sound trill mean that the Mainte
-
nance mode is ON.
◊ 2 audible signals and 1 sound trill mean that the Main
-
tenance mode is OFF.
3
Turn the ignition off.
