English
English
Setting up the TEAM RoadCom-FS
1) Installation of a CB antenna
The antenna is one of the most important parts of the equipment. The type of antenna and its
location has a great effect on the range of operation. Please consider the following criteria for
selecting the best location and installation of your antenna:
> Make sure that the antenna is designed for radio operation on 27 MHz.
> The location of the antenna should be as high as possible without any obstacles nearby.
> The aerial cable should not be damaged and the plugs should be properly connected.
> Make sure that the antenna cable is not bent too strong.
> The bigger the mechanical size of the antenna, the higher the range of operation.
When you install a mobile antenna please note the following advice:
> The antenna should be fixed in the centre of a bigger part of the coachwork.
> The mobile antenna coil should have the closest possible contact with a conducting metallic
surface of the bodywork of the car.
There are also some other possibilities to fix the antenna onto the car without the necessity
to drill a hole into the bodywork of your car, for example mounting the antenna onto the gut-
ter, mounting the antenna onto a holder on the cover of the boot or using an antenna with a
magnetic foot or using a windscreen antenna.
> All connected cables including the antenna cable must not exceed a length of 3 m.
2) Aerial Connection
Before pressing the transmit key, a suitable aerial must be connected. The PL259 plug of the
aerial cable (coax) is connected to the SO239 socket (21) on the rear panel. Make sure, that
all plugs are firmly tightened and properly soldered. Unsatisfactory connections can damage
the radio and will reduce the range of operation.
The antenna should be matched with the radio, otherwise a part of the transmit power will be
reflected at the antenna and will not be radiated. This causes also a drop in the range of oper-
ation. The matching can be carried out by a length adjustment of the antenna radial for a min-
imal SWR ratio which can be measured by a SWR meter (e. g. TEAM SWR 1180P). After the
measurement the SWR meter should be removed from the antenna line.
3) Installation in the car
When you want to fix the unit in your car, you can either fasten it with the help of the includ-
ed mounting bracket below the dashboard, or insert it into a car radio slot by using the includ-
ed inserting frame. Always mount the transceiver where the switches are easily accessible.
Other important points of view for the correct mounting position are:
TABLE OF CONTENTS
Setting up the TEAM RoadCom-FS
1) Installation of a CB antenna
15
2) Aerial Connection
15
3) Installation in the car
15 - 16
4) Microphone DM-106S
16
5) Power source
16
Operation of the TEAM RoadCom-FS
1) Switching on [
Vol/Off
] 17
2) Squelch [
SQ/Asq
]
17
3) Confirmation tones
17
4) Channel selection [
p
] [
q
]
17
5) Audio reproduction sound selection [
Hi/Lo
]
17
6) LCD background illumination [
B
]
18
7) Modulation selection [
Mode
]
18
8) Version selection [
DE/EC/EI/EU/PL/UK
]
18
9) Transmitting
19
10) Call tone
19
11) CTCSS [
CTCSS
] & [
SET
]
19
12) Last channel recall [
LCR
]
19
13) Priority Channel 9 [
CH9/19
] 19
14) Channel scanning [
Scan
]
20
15) Dual watch function [
Dual Watch /
]
20
16) Key lock function [ ]
20 - 21
17) VOX function
21
18) External speaker jack
21
19) External signal meter jack
21
Additional Information
1) Safety Instructions
22
2) General Precautions
22
3) Servicing
22
4) Conformity
22
Schematic Diagram
32 - 34
Channel Frequencies
35
Specifications
63
14
15
roadcom-FS-FMN_manual_09052012_V1_mod:RoadCOM manual.qxd 24.05.2012 13:18 Seite 14
