If only one lobe pattern can be observed or if two lobes become one
pattern, the head is not on the alignment check track.
In such event, execute step-in or step-out as follows to obtain the
most similar waveform to that in Fig.430.
Step operation can be
done by key "8" (STEP-IN) and key "9” (STEP-OUT). By a depression
of these keys, head will move for one track space.
48tpi:
2 tracks
96tpi:
4 tracks
Note: The above number of tracks to be stepped is required to make the
alignment track position be fit with the magnetized condition of
the basic magnetized phase MA M of the stepping motor.
For a 48tpi FDD, the lobe pattern as in Fig.430 should be observed
at the track of even number. For a 96tpi FDD, the lobe pattern
should be observed at the track of multiple number of four (4) .
(j) For a 96tpi, confirm that the H GAIN indicator of the SKA turns on
in order to improve the measurement accuracy and switching of
humidity coefficient.
If it is off, turn it on by depressing "DD"
key.
(fc) Key in "E3” (ALIGNMENT)
Calibration value of the alignment disk and environmental relative
humidity should be set previously in the SKA.
(L) Confirm all the indications on the DATA m i l (%) indicator are
within ±30%*
The initial digit of the DATA indicator is the symbol.
h
(+) mark
indicates that the head is shifted inward from the reference position,
while - mark indicates that the head is shifted outward.
t
(m) For a double sided FDD, execute the same check for side 1 head
according to the following procedure.
4100
Содержание FD-55 Series
