background image

ADCP-92-159 • Issue 1 • 2/2015

Page 3

© 2015, Tyco Electronics Corporation

Admonishments

Important safety admonishments are used throughout this manual to warn of possible hazards to 
persons or equipment. An admonishment identifies a possible hazard and then explains what 
may happen if the hazard is not avoided. These warnings are flagged by use of the triangular 
alert icon (seen below) and are listed in descending order of severity of injury or damage and 
likelihood of occurrence.

1

DESCRIPTION

The FPX 1RU and 2RU panels can accommodate up to 48 and 96 terminations, respectively. 
Typically, the panel ships empty. The panel may also be ordered with adapter packs, Multifiber 
Push-On (MPO) cassettes, splice trays, or pigtails. The panel can be configured for termination 
only (without splice trays) or for termination/splice. 

Figure 1

 shows the 2RU panel. 

 

Figure 1. FPX 2RU Panel (Front View)

Danger: 

Danger is used to indicate the presence of a hazard that 

will

 cause severe personal 

injury, death, or substantial property damage if the hazard is not avoided.

Warning: 

Warning is used to indicate the presence of a hazard that 

can

 cause severe personal 

injury, death, or substantial property damage if the hazard is not avoided.

Caution: 

Caution is used to indicate the presence of a hazard that 

will

 or 

can

 cause minor 

personal injury or property damage if the hazard is not avoided.

Note: 

The Fiber Panel Next Generation is designed to be installed in an environmentally 

controlled network telecommunications facility such as a Central Office, Controlled 
Environmental Vault, or Data Center. 

Caution: 

Adapter packs and MPO cassettes should not be both used in the same panel.

25677-A

Содержание FPX Series





























Отзывы: