background image

ADCP-92-159 • Issue 1 • 2/2015

Page 16

© 2015, Tyco Electronics Corportation

3.6

Preparing and Connecting a Pre-Connectorized Cable

This section tells how to prepare and connect a multi-fiber cable. The cable being installed must 
conform to the breakout dimensions provided. 

Use the following procedure.

1. If the cable is being connectorized:

a.

Refer to 

Table 2

 for breakout dimensions for variables L2 to L5.

b. Associate these variables to the breakout diagrams given in 

Figure 17

 (IFC Stranded) 

Figure 18

 (IFC Ribbon), or 

Figure 19

 (OSP) for the cable type being installed. 

2. Determine the correct clamp and grommet combination required to secure the cable to the 

panel. For details on the cable clamp itself, refer to 

Section 3.4 on Page 14

.

3. Determine the cable entry location. Cables may enter the panel from either top or bottom 

and may be clamped to either the left or right side. 

Figure 17. IFC Stranded Cable Breakout Dimensions

Table 2. Breakout Dimensions

(NOTE: Dimensions are the same for 1RU and 2RU panels.)

CABLE TYPE

FIGURE

L2

L3

L4

L5

IFC Stranded

Figure 17

52.0 in
(132.1 cm)

25.25
(64.1 cm)

N/A

53.25
(135.3 cm)

IFC Ribbon

Figure 18

50.75 in
(128.9 cm)

24.75 in
(62.9 cm)

26 in
(66 cm)

53.25
(135.3 cm)

OSP Ribbon 
Cable

Figure 19

52.75 in
(134 cm)

24.75 in
(62.9 cm)

28 in
(71.1 cm)

54.75 in
(139.1 cm)

OSP/IFC
CABLE

FANOUT LENGTH

 

‘L3’ +0.0 IN./-6.0 IN.

(+0.0 CM/-15.2 CM)

BREAKOUT LENGTH

 

‘L2’ +0.0 IN./-6.0 IN.(+0.0 CM/-15.2 CM)

MULTIFIBER

SUBUNITS

CONNECTORS

HEATSHRINK

6.0 IN. (15.2 CM)

CLAMP

25717-A

CLAMP POSITION

 

‘L5’ +0.0 IN./-6.0 IN.(+0.0 CM/-15.2 CM)

Содержание FPX Series





























Отзывы: