background image

 

Page 

9

 of 

11

 

 

TDK-Lambda 

DBM20 

 

INSTRUCTION MANUAL

 

PA640-04-01B 

5.2. Mounting spacing vs. airflow

  

 

 
 
 

 
 

   

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

5.3.  terminal on input/output connector 

 terminal must be connected to the Protective earth 

terminal of the equipment. If not connected to the 
Chassis(Conductor), the conducted noise, radiation noise 
and output noise will increase.

 

 

5.4. Buffer Module mounting on DIN RAIL (TS35 

or equivalent) 

Make sure input and output wires are disconnected before 
mounting buffer module onto rail 

 

5.4.1 Refer to figure 14. 
5.4.2 Tilt the unit slightly rearwards, fit the unit                

                  over top hat rail 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Figure 14 

 

Figure 13 

Do not exceed the buffer derating. Please refer to section 6. Leave enough space surround the units to ventilate heat 
efficiently.

 

Minimum Installation clearances: 
40mm on top, 20mm at the bottom, A=5mm which is recommended on the left and right side when products are permanently 
loaded with full 480W in Ready mode.  
In case the adjacent device is a heat source, A=15mm clearance is recommended.  
 
The ambient temperature (T

a

) is reference 20mm from the bottom of the unit.  

2 0 m m
o r
m o re

2 0 m m
o r
m o re

4 0 m m
o r

m o re

4 0 m m
o r

m o re

A ir Flo w

A

A

D ISC H A R G IN G

C H A R G IN G

2 4 V D C /2 0A

+ V

D B M 2 0

1

+ V ‐V ‐V

2

3

4

4  +

3  B u ffe r

2  R e ad y

1  In h ib it

D ISC H A R G IN G

C H A R G IN G

24 V D C /20 A

+ V

D B M 2 0

1

+ V ‐V ‐V

2

3

4

4  +

3  B u ffe r

2  R e a d y

1  In h ib it

D R F 4 8 0 ‐2 4 ‐1

2 4 V D C /20 A

+ V + V ‐V ‐V

D C

O K

D C  O K

V . A D J

P E A K

10 0 ‐2 4 0 V A C

N

L

TD

TD

TD

F IX E D  M O D E

V IN ‐1

B u ffe r

Le v e l

FIX E D  M O D E

V IN ‐1

B u ffe r

L e ve l

 

Содержание DBM20












Отзывы: