TC Electronic SYSTEM 6000 MKII Скачать руководство пользователя страница 112

Страница: 112 / 124

112

lM6

Basic Use

LM6 makes use of a unique way of visualizing short-term loudness, loudness history, and long-term statistical descriptors.

It may be used with mono, stereo and 5.1 material for any type of program material.

Press the Radar key to bring up the Radar page. This page will be used most of the time. The basic functionality of the

Radar page is shown in Fig 3.

Fig 3 - Radar page features of LM6 in System6000

Target Loudness is displayed at 12 o’clock of the outer

ring, and at the bold circle of the radar indicated also by the

transition from green to yellow. The descriptors Loudness

Range and Program Loudness, are the yellow numbers in

the lower part of the display. Press the Reset key to reset

Radar and Descriptors.

The “Transport Controls”, Pause and Reset, are used to

make the radar and descriptor measurements run, pause

and reset. Press the “Main” key to change preset name

and for adjusting more parameters. Press the “Setup”

key to change setup parameters. Presets can be stored

specifying target loudness, noise floor, overload conditions

etc using normal System6000 preset handling procedures.

Radar Page

Current Loudness: Outer Ring

The outer ring of the Radar page displays Momentary

loudness. The 0 LU point (i.e. Target Loudness) is at 12

o’clock, and marked by the border between green and

yellow, while the Low Level point is marked by the border

between green and blue. The “0 LU Equals” and “Low

Level Below” parameters are found on the Setup page. For

instance, if 0 LU is set at -22 LUFS, and Low Level is set

at -20 LU, the color coding of Fig 3 applies.

The user should be instructed to keep the outer ring in

the green area, and around 12 o’clock on the average.

Excursions into the blue or the yellow area should be

balanced, and not only go in one direction.

The numbers associated with the outer ring may be

referenced at either maximum loudness, or have a zero

point set set at Target Level. Choose “LUFS” or “LU” at the

Loudness Scale selection on the Main page depending on

your preference. Either way of looking at loudness is valid.

LUFS reading is in line with how peak level is typically

measured in a digital system, and compatible with Dolby

AC3 and E metadata, while the LU approach calls for a

certain Target Loudness to have been predetermined, like

e.g. a VU meter.

Note how “LUFS” in some countries is called “LKFS”, but

the two are identical. A reading of, for instance, -25.0 LUFS

is the precise same as -25.0 LKFS.

Содержание SYSTEM 6000 MKII





























































































































Результаты поиска

Содержание SYSTEM 6000 MKII

Отзывы:

TC Electronic SYSTEM 6000 MKII, Руководство по алгоритмам, Страница: 112 / 124

Результаты поиска

Содержание SYSTEM 6000 MKII

Отзывы: