TC Electronic SYSTEM 6000 MKII Скачать руководство пользователя страница 108

Страница: 108 / 124

108

bACkDrOP - TuTOrIAl

preserved as you switch, allowing you to compare your

best settings for each.

It is also a good idea to periodically use the Removed

button to hear what is being removed from the input signal.

If you hear components of the signal, then this may be an

indication that you are applying too much processing.

Finally, if you are working on a stereo recording, it is

worthwhile to try using BackDrop in both Stereo and

M/S modes. For certain audio sequences a dramatic

improvement in quality can be obtained by performing the

noise reduction processing in the M/S domain. You should

note that, in order to get the most from the M/S domain

processing, the controls should be unlinked so that different

amounts of processing can be applied to the Mid and Side

signals. Specifically, it is often more perceptually beneficial

to apply more noise reduction to the Side signal than to the

Mid signal.

Common Questions

1) Is it better to get as long a noise print as possible?

The simple answer is yes, but the maximum length of the

capture buffer is 1.5 seconds. So there is no advantage

to having a noise print that is longer than 1.5 seconds.

BackDrop doesn’t need more than 1.5 seconds in order to

fully train itself on the noise in the signal.

2) Is it important to get a very good loop of the noise?

Again the answer is yes. If there is some signal in the

captured buffer then BackDrop will not train itself properly

about the nature of the noise that you are trying to remove.

That is, it will try to remove part of the signal as well.

3) What if it is not possible to get a noise print?

This, of course, will limit BackDrop’s ability to decide what

is noise and what is signal. There are two approaches you

can use in this case.

a) Find another piece of audio with similar noise and use it

to capture the noise print information.

b) Find the quietest part of the audio signal and use it to

capture the noise print information. Then use the MultiType

algorithm model to apply the noise reduction. Set the Buzz

Aggression and Room Aggression controls to 0%. Use the

Hiss Aggression to control the amount of noise reduction.

This isn’t perfect, but it should let you achieve some

broadband noise reduction.

4) Should I try to remove all the noise?

Often it is desirable to leave some background noise in

the signal so that it doesn’t sound unnaturally clean. This

is primarily true for an overall mixed signal rather than for

individual tracks that are yet to be mixed together.

5) Do I always have to use Play, Trim Start/End and

Calculate to get a good loop?

No. This is usually required when working with a tape

transport or when taking a print of a live room where it may

be hard to anticipate the material.

If you are working with tracks on a hard disk recording

system, it is often handy play a noise-only portion of the

track in loop-mode before pressing the Capture button.

6) Can I practice using Backdrop’s controls by capturing

noise and using the capture buffer in Play mode?

You can use this technique for quick control checks but it is

not recommended for choosing final settings.

Since Backdrop’s strength lies in allowing you to precisely

control the amount of reduction to apply without altering

the signal, it is always better to fine-tune the controls with a

passage containing music. Focussing too much on just the

noise can lead you to over-processing, giving unfavorable

results when you listen to the entire signal.

Содержание SYSTEM 6000 MKII





























































































































Результаты поиска

Содержание SYSTEM 6000 MKII

Отзывы:

Похожие инструкции для SYSTEM 6000 MKII

Бренды по названию

Популярные бренды

TC Electronic SYSTEM 6000 MKII, Руководство по алгоритмам

Результаты поиска

Содержание SYSTEM 6000 MKII

Отзывы:

Похожие инструкции для SYSTEM 6000 MKII

Бренды по названию

Популярные бренды