Taylor-Dunn Bigfoot G-1500 Скачать руководство пользователя

Страница: 82 / 118

Hardware

Page 82

Bigfoot G-1500

MB-440-10

TORQUE GUIDELINES FOR STANDARD HARDWARE

Note: Torque values specified are for clean dry threads.

Note: Torque value used should be for lowest grade of hardware used. If a grade 2 nut is used on a grade 8

bolt, use grade 2 torque value.

Hardware Identification

Hex Head Bolts and Screws

The grade of SAE bolts and screws are identified by markings on the head

as illustrated to the right.
The grade of a metric hex head bolt or screw is cast directly on the head.

Below is an example of a 10.9. The location and style of the text will vary.

SAE Grade 2

SAE Grade 5

SAE Grade 8

SAE Grade 9

Other types of bolts and screws

Truss Head, Grade 2

Carriage Bolt, Grade 2

Содержание Bigfoot G-1500























































































































Результаты поиска

Содержание Bigfoot G-1500

Отзывы:

Похожие инструкции для Bigfoot G-1500

Бренды по названию

Популярные бренды

Taylor-Dunn Bigfoot G-1500, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание Bigfoot G-1500

Отзывы:

Похожие инструкции для Bigfoot G-1500

Бренды по названию

Популярные бренды