Taylor-Dunn Bigfoot G-1500 Скачать руководство пользователя

Страница: 64 / 118

Batteries

Page 64

Bigfoot G-1500

MB-440-10

ADJUSTMENT

1: Loosen the ball joint jam nut and the cable

mounting nuts on the spring steel mounting plate.

2: Disconnect the coupler from the ball joint at the

transmission.

3: Place the shift lever in forward.

4: Move the transmission shift lever to the forward

detent.

5: Using the cable nuts and/or the ball joint coupler,

adjust the linkage so that the coupler easily slides

onto the ball joint.

6: Tighten all mounting and jam nuts.

7: While slowly rotating the transmission input

sheave, shift the transmission from forward to

reverse and back to forward to confirm proper

adjustment.

8: Reconnect the battery and test drive.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

Do not modify the stainless steel shift cable mounting

plate at the transmission. This mounting plate is

spring steel and functions as an active part of the

shifting mechanism. Modification of this mounting

plate may cause improper operation of the shift

linkage resulting in damage to the transmission.

NOTICE

Содержание Bigfoot G-1500























































































































Результаты поиска

Содержание Bigfoot G-1500

Отзывы:

Похожие инструкции для Bigfoot G-1500

Бренды по названию

Популярные бренды

Taylor-Dunn Bigfoot G-1500, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание Bigfoot G-1500

Отзывы:

Похожие инструкции для Bigfoot G-1500

Бренды по названию

Популярные бренды