Taylor-Dunn Bigfoot G-1500 Скачать руководство пользователя

Страница: 34 / 118

Steering

Page 34

Bigfoot G-1500

MB-440-10

FRONT WHEEL ALIGNMENT

Refer to the Front Axle section for front wheel alignment

procedure.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

INSPECT BALL JOINTS

Note: A set of ball joints and/or rod ends will wear

at the same rate. If a ball joint and or rod end

is worn out, then all should be replaced as

a set.

1: Tie off the front wheels so that they cannot turn.

2: While watching the ball joints, rapidly rotate the

steering wheel to the left and right.

3: If the housing moves up or down on the shaft

then the ball joint is worn out and should be

replaced. Refer to section Replace Ball Joint for

information regarding replacing ball joints.

4: Untie the front wheels.

5: Reconnect the main positive and negative cables

at the batteries.

6: Remove the blocks from behind the wheels.

7: Release the parking brake and test drive.

REPLACE BALL JOINT

Note: In many cases the removal of a ball joint

may cause damage to the ball joint. It is

recommended that if a ball joint is removed

then it should be replaced.

1: Raise the front of the vehicle and support with

jack stands.

2: Loosen the ball joint jam nut.

3: Remove the ball joint nut.

4: Using a ball joint separator or pickle fork, remove

the ball joint from the steering arm.

5: Remove the ball joint from the tie rod.

6: Install the new ball joint into the steering sleeve.

7: Install the ball joint into the steering arm. Tighten

the ball joint nut per torque listed in the Hardware

Torque table at the end of this section.

8: Realign the front wheels. Refer to the Front Axle

section for information regarding realignment of

the front wheels.

9: Lower the vehicle.

10: Reconnect the main positive and negative cables

at the batteries.

11: Release the park brake and test drive.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

Typical Ball Joint Separator

Typical Pickle Fork

Ball Joint

Содержание Bigfoot G-1500























































































































Результаты поиска

Содержание Bigfoot G-1500

Отзывы:

Похожие инструкции для Bigfoot G-1500

Бренды по названию

Популярные бренды

Taylor-Dunn Bigfoot G-1500, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание Bigfoot G-1500

Отзывы:

Похожие инструкции для Bigfoot G-1500

Бренды по названию

Популярные бренды