Taurus SEBR7140, Руководство по сборке и эксплуатации

Страница: 30 / 60

Assembly step 5
15
No. Descrip � on Note Qty.
10 lock nut M10 14
11 big gasket Φ 10 34
12 hexagon bolt M10*90 2
14 plas � c cover 34
30 hexagon bolt M10*50 4
31 cover 2
32 pulley catch plate 4
50 hexagon bolt M10*85 2
52 cable Φ 5*7920mm 2
54 pulley Φ 95 12
55 pulley Φ 60 2
56 hexagon bolt M10*45 8
84 hexagon bolt M10*20 4
52
10
84
14
50
31
54
30
56
56
56
56
32
Assembly step 2
25
23
11
14
24
22
21
9
84
14
9
12
14
10
11
10
14
14
11
14
11
10
14
Assembly step 5
15
No. Descrip � on Note Qty.
10 lock nut M10 14
11 big gasket Φ 10 34
12 hexagon bolt M10*90 2
14 plas � c cover 34
30 hexagon bolt M10*50 4
31 cover 2
32 pulley catch plate 4
50 hexagon bolt M10*85 2
52 cable Φ 5*7920mm 2
54 pulley Φ 95 12
55 pulley Φ 60 2
56 hexagon bolt M10*45 8
84 hexagon bolt M10*20 4
52
10
84
14
50
31
54
30
56
56
56
56
32
Assembly step 5
15
No. Descrip � on Note Qty.
10 lock nut M10 14
11 big gasket Φ 10 34
12 hexagon bolt M10*90 2
14 plas � c cover 34
30 hexagon bolt M10*50 4
31 cover 2
32 pulley catch plate 4
50 hexagon bolt M10*85 2
52 cable Φ 5*7920mm 2
54 pulley Φ 95 12
55 pulley Φ 60 2
56 hexagon bolt M10*45 8
84 hexagon bolt M10*20 4
52
10
84
14
50
31
54
30
56
56
56
56
32
30
Elite Complete Trainer
Step 8: Cable Adjustment
You can recognize the correct cable tension when the top weight plate rests very lightly on the
weight stack. If the top weight plate is hanging in the air, the cable is too tight. If the cable is visibly
slacking, it is too loose. If the cable is slacking or too tight, it needs adjustment. There are three points
at which the cable can be adjusted. There is one adjustment point for coarser adjustments and two
adjustment points for finer adjustments.
Coarse Adjustment
Coarser adjustments can be made on the pulley bracket that is connected to the weight stack. There
are four adjustment holes on the regular pulley bracket and two on the pulley bracket with added
weight.
1. To tighten the cable, attach the pulley to a lower hole.
2. To loosen the cable, attach the pulley to a higher hole.
Fine Adjustment
In some cases, only finer adjustments are needed. There are two ways to do so.
+ bolt end of the pulley bracket
+ bolt end of the cable
⚠ WARNING
Both bolt ends must always be screwed in at least 1/3.
Option 1: Bolt End of the Pulley Bracket
If already attached, first remove the pulley as it will otherwise rotate when
adjusting.
1. To loosen the cable, turn counterclockwise.
2. To tighten the cable, turn clockwise.
Option 2: Bolt End of the Cable
1. Loosen the nuts.
2. Screw or unscrew the bolt end to the desired length.
3. Tighten the nuts.
Coarse adjustment
Fine adjustment