Tatu Marchesan GAPCW 8013 Скачать руководство пользователя страница 9

Страница: 9 / 64

Marchesan Implementos e Máquinas Agrícolas “TATU” S.A.

GAPCW 8013 / GASPCW 9017

Transportation over truck or trailer

To the operator

Marchesan does not advise the equipment traffic on highways, because this

practice involves serious security risks and it is prohibited by the current existing

traffic law. The transportation for long distances should be done on truck, trailer

or others by following these safety guidelines:

• Use adequate ramps to load or unload the equipment. Do not make the loading

on ditch banks, it can cause a serious accident.

• When lifting with a hoist, use the appropriate points to lift.

• Underpin the equipment properly.

• Use chock blocks and safety chains to secure the equipment to the truck or

trailer during the transport.

• Make sure the SMV (Slow Moving Vehicle) sign and all the lights and reflectors

that are required by the local highway and transport autorithies are in place,

clean and can be seen clearly by all overtaking and oncoming traffic.

• After 8 to 10 km transporting, please inspect the load condition. Repeat this

procedure every 80 to 100 km. Give more attention when transporting the

equipment on rough roads, slopes and other adverse conditions.

• Always be careful with the load height, especially when passing under electrical

power lines, bridges and others.

• Check all laws and regulations regarding the height limits and load width while

transporting the equipment on truck or trailer. If necessary, use banners, lights

and other devices, in order to give adequate warning to the other drivers.

Содержание GAPCW 8013

































































Результаты поиска

Содержание GAPCW 8013

Отзывы:

Бренды по названию

Популярные бренды

Tatu Marchesan GAPCW 8013, Руководство оператора

Результаты поиска

Содержание GAPCW 8013

Отзывы:

Бренды по названию

Популярные бренды