manualshive.com logo in svg

Tatu Marchesan GAPCW 8013, Руководство оператора

Поделиться
Скачать
Tatu Marchesan GAPCW 8013 Скачать руководство пользователя страница 38

36

Marchesan Implementos e Máquinas Agrícolas “TATU” S.A.

GAPCW 8013 / GASPCW 9017

Set-up instructions

The following instructions must be carefully observed to get the best working 

performance.

Preparing the tractor

The addition of ballast water in the tires, a set of weights on the front part and rear 

wheels of the tractor are the most used ways to increase the soil traction and give greater 
stability to the tractor. Check if the tractor is in full conditions before using it.

Preparing the disk harrow

Check the condition of all parts and retighten nuts and bolts, especially the ones from 

the disc gangs. If the gangs work loose, they may damage the axle and other components.

Check the tires inflation and keep the same pressure on both of them.

Lubricate all grease fittings appropriately. (See the instructions on the 'lubrication' 

section).

Hitching to the tractor

Couple the drawbar (B) to the tractor drawbar using an axle (C). Note that the drawbar 

is centralized on the tractor. To facilitate hitching, use the jack (D) adjustment.

Lock the chain (E) to the equipment and tractor to assure that they will not get loose, 

but leave a small clearance so that the disk harrow can perform maneuvers.

Approach the tractor and couple the 

hoses (A) to the quick couplers. To do so, 
shut down the engine, relieve the control 
valve pressure by activating the lever 
a couple of times and check if the quick 
couplers are clean.

Tractor 

Tractor 

PTO

PTO

A

A

Содержание GAPCW 8013

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды