Tatu Marchesan GAPCW 8013 Скачать руководство пользователя страница 48

Страница: 48 / 64

Marchesan Implementos e Máquinas Agrícolas “TATU” S.A.

GAPCW 8013 / GASPCW 9017

Troubleshooting guide

Adjustments and operations

PROBLEM

CAUSES

POSSIBLE SOLUTIONS

Quick couplers

do not adapt.

Different type of quick

couplers.

Use male and female quick couplers

from the same type.

Hoses leaking

with fixed

terminals.

Insufficient tightening.

Retighten carefully.

Lack of sealing material on

the thread.

Use thread sealing tape and retighten

carefully.

H y d r a u l i c

cylinder leaking.

Damaged repairings.

Replace the repairings.

Damaged rod.

Replace the rod.

Oil with impurities.

Replace the oil, repairings and filter

elements.

Working pressure superior

than the recommended

one.

Adjust the control valve using the

relief valve with the aid of a pressure

gauge.
Normal pressure: 180 Kgf/cm

Quick couplers

leaking.

Insufficient tightening.

Retighten carefully.

Lack of sealing material on

the thread.

Use thread sealing tape and retighten

carefully.

Damaged repairings.

Replace the repairings.

Содержание GAPCW 8013

































































Результаты поиска

Содержание GAPCW 8013

Отзывы:

Бренды по названию

Популярные бренды

Tatu Marchesan GAPCW 8013, Руководство оператора

Результаты поиска

Содержание GAPCW 8013

Отзывы:

Бренды по названию

Популярные бренды