Task Force Tips MONSOON MONITOR Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 44

background image

TASK FORCE TIPS, Inc.

2800 E. Evans Ave., Valparaiso, IN 46383-6940 USA

800-348-2686 • 219-462-6161 • Fax 219-464-7155

10.0 WARRANTY

Task Force Tips, Inc., Valparaiso, Indiana 46383-6940 (“TFT”) warrants to the original purchaser of its Monsoon and
Monsoon RC Monitor (“equipment”), and to anyone to whom it is transferred, that the equipment shall be free from defects
in material and workmanship during the five (5) year period from the date of purchase.

TFT’s obligation under this warranty is specifically limited to replacing or repairing the equipment (or its parts) which are
shown by TFT’s examination to be in a defective condition attributable to TFT. To qualify for this limited warranty, the
claimant must return the equipment to TFT, at 2800 East Evans Avenue, Valparaiso, Indiana 46383-6940, within a
reasonable time after discovery of the defect. TFT will examine the equipment. If TFT determines that there is a defect
attributable to it, it will correct the problem within a reasonable time. If the equipment is covered by this limited warranty,
TFT will assume the expenses of repair.

If any defect attributable to TFT under this limited warranty cannot be reasonably cured by repair or replacement, TFT may
elect to refund the purchase price of the equipment, less reasonable depreciation, in complete discharge of its obligations
under this limited warranty. If TFT makes this election, claimant shall return the equipment to TFT free and clear of any
liens and encumbrances.

This is a limited warranty. The original purchaser of the equipment, any person to whom it is transferred, and any person
who is an intended or unintended beneficiary of the equipment, shall not be entitled to recover from TFT any consequential
or incidental damages for injury to person and/or property resulting from any defective equipment manufactured or
assembled by TFT. It is agreed and understood that the price stated for the equipment is in part consideration for limiting
TFT’s liability. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
may not apply to you.

TFT shall have no obligation under this limited warranty if the equipment is, or has been, misused or neglected (including
failure to provide reasonable maintenance) or if there have been accidents to the equipment or if it has been repaired or
altered by someone else.

THIS IS A LIMITED EXPRESS WARRANTY ONLY. TFT EXPRESSLY DISCLAIMS WITH RESPECT TO THE
EQUIPMENT ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND ALL IMPLIED WARRANTIES OF FITNESS
FOR A PARTICULAR PURPOSE. THERE IS NO WARRANTY OF ANY NATURE MADE BY TFT BEYOND THAT STATED
IN THE DOCUMENT.

MADE IN USA • www.tft.com

©Copyright Task Force Tips, Inc. 2004-2007

LIY-200 March 1, 2007 Rev05

«
...
42
43
44

Содержание MONSOON MONITOR













































Отзывы:

Нет отзывов

Похожие инструкции для MONSOON MONITOR

Бренд: Waterwise Страницы: 12

Бренд: ParaBody Страницы: 38

Бренд: Modulate Страницы: 2

Бренд: Ecler Страницы: 108

Бренд: R&S Страницы: 121

Бренд: iFIT Страницы: 11

Бренд: SandenVendo Страницы: 19

Бренд: Yamaha Страницы: 48

Бренд: Yamaha Страницы: 85

Бренд: Yamaha Страницы: 43

Бренд: Yamaha Страницы: 200

Heart Guardian AED

Бренд: Radian Страницы: 36

UltraVent XS Plus 6 2/3 E

Бренд: Rational Страницы: 220

VLR100 LED Series

Бренд: WE-EF Страницы: 3

Бренд: Lumineux Страницы: 2

Бренд: RAB Страницы: 4

Бренд: Marani Страницы: 35

Бренд: Wacker Neuson Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды