Task Force Tips MONSOON MONITOR Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 44

background image

35

6.4.3 MONSOON MONITOR FRICTION LOSS

Fig 6.5.1 - TFT Stack Tip Integral Stream Straightener Friction Loss

Fig 6.4.3F - Monsoon Monitor Friction Loss

0

1000

2000

3000

4000

5000

6000

7000

(LPM)

0

500

1000

1500

2000

Flow (GPM)

0.0

0.2

1.2

1.0

0.8

0.6

0.4

PRES

SURE

(BAR)

15 PSI AT 2000 GPM

20

8

12

16

4

0

PRES

SURE

(PSI)

MONSOON MONITOR FRICTION LOSS

4 PSI AT 1000 GPM

20

8

12

16

4

0

PRES

SURE

(PSI)

0

500

1000

1500

2000

Flow (GPM)

13 PSI AT 2000 GPM

0.0

0.2

1.2

1.0

0.8

0.6

0.4

PRES

SURE

(BAR)

0

1000

2000

3000

4000

5000

6000

7000

(LPM)

TFT STACKED TIP INTEGRAL STREAM
STRAIGHTENER FRICTION LOSS

3 PSI AT 1000 GPM

6.5.1 STREAM STRAIGHTENERS WITH STACKED TIP NOZZLES

Turbulence though the Monsoon
Monitor is very low but stream quality
and reach can be improved with the
u s e

o f

t h e

i n t e g r a l

s t r e a m

straightener on the TFT stacked tip
nozzle. See figure 6.5.1 for the
stacked tip's integral stream
straightener friction loss.

6.5 STREAM STRAIGHTENERS

GPM

FL
OW

920

840

751

1127

1063

1246

1188

994

80

90

110

100

50

60

40

70

PSIPSI

PRES

S.

GPM

FL
OW

705

643

761

862

814

575

954

910

50

90

110

100

60

80

70

PSIPSI

PRES

S.

40

473

518

634

598

559

701

668

110

100

60

70

90

80

GPM

FL
OW

423

PSIPSI

50

40

PRES

S.

FL
OW

GPM

435

397

355

533

502

589

562

470

PSIPSI

70

80

90

110

100

50

60

40

PRES

S.

OK

6.5.2 STREAM STRAIGHTENERS WITH FOG NOZZLES

When using a fog nozzle it is
recommended that no stream
straightener be used since the fog
nozzle's flow path generally serves
as a stream straightener. Use of a
stream straightener with a fog nozzle
will increase the stresses on the
monitor's gear train and may lead to
premature wear.

NOT OK

«
...
33
34
35
36
37
...
»

Содержание MONSOON MONITOR













































Отзывы:

Нет отзывов

Похожие инструкции для MONSOON MONITOR

Бренд: ABB Страницы: 50

ACS880-01 Series

Бренд: ABB Страницы: 17

Бренд: ABB Страницы: 36

Бренд: Makerfire Страницы: 10

Бренд: GE Страницы: 24

Бренд: ParaBody Страницы: 5

Бренд: Baileigh Industrial Страницы: 28

Бренд: Baileigh Industrial Страницы: 56

Бренд: Raven Страницы: 12

Бренд: Zero 88 Страницы: 20

Бренд: Kapriol Страницы: 32

Бренд: Cabletron Systems Страницы: 33

Бренд: i-CAT Страницы: 32

Бренд: S.R.Smith Страницы: 8

Бренд: S.R.Smith Страницы: 23

NavBoard ZipFlip

Бренд: S&S Precision Страницы: 6

Бренд: Gardco Страницы: 17

Бренд: H&S Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды