manualshive.com logo in svg

Tarter RT205BL, Руководство по эксплуатации и сборке

Поделиться
Скачать
Tarter RT205BL Скачать руководство пользователя страница 15

15

ASSEMBLY

BEFORE PUTTING YOUR ROTARY TILLER INTO 

SERVICE

IMPORTANT: This tiller was shipped without oil in 

the gearboxes and without grease in the the grease 

fittings. UNIT MUST BE SERVICED BEFORE USE.

NOTE: Fill the gearboxes using EP 85-90W gear 

oil. For all grease fittings use TYPE/Grade II tube 

grease. 

1. Please ensure that your Rotary Tiller is secure and 

level. 

2. Using a      wrench, remove the 1/2” vented pipe 

plug located on top of the gearbox, above the PTO 

shaft.

3. Remove the check plug, located on the back of the 

gearbox.

4. Fill the gearbox using specified gear oil, until oil 

begins to overflow from the check plug hole in the 

rear. (Holds approx. 1-1/2 quarts.)

5. Replace and tighten the check plug.

DO NOT overfill gearbox. This could 
cause damage to oil seals and can cause 
permanent damage to the gearbox. This 
issue will not be covered under warranty.

CAUTION 

6. Replace and tighten the 1/2” vented pipe plug and 

clean away any excess oil.

7. Using a     wrench, remove the 1/2” pipe plug 

located at the top of the side gearbox and the 1/8” 

check plug located on the side of the side gearbox.

8. Fill the side gearbox using specified gear oil until 

the oil begins to overflow from the check plug hole. 

(Holds approx. 2-1/2 quarts.)

9. Replace and tighten the 1/2” vented pipe plug and 

the 1/8” check plug. Clean away any excess oil. 

DO NOT overfill gearbox. This could 
cause damage to oil seals and can cause 
permanent damage to the gearbox. This 
issue will not be covered under warranty.

CAUTION 

10. Grease the grease fitting on the out-board hub.

11. Grease the two grease fittings on the PTO 

universal joints.

12. Grease the two grease fittings on the PTO 

safety shield.

13. Separate the PTO shaft and grease the inner 

surface.

Содержание RT205BL





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды