Target PRO 35 III DIESEL, Руководство по эксплуатации

Страница: 26 / 46

26
•
Move the saw forward or reverse slowly by pushing or
pulling on the Speed Control Lever (1S). Move the
saw slowly to prevent stalling the blade. Make sure the
Front Guide (3C), Rear Guide (3D) and the
Diamond Blade (2E) stay on the line.
•
Lower the saw by pushing the Toggle Switch (1R) down
on the Speed Control Lever (1S) until the Diamond
Blade (2E) is at the desired cutting depth (See “Blade
Cutting Depth Information—Below).
Blade Cutting Depth Information:
This saw is equipped with a Blade Depth Indicator (1K)
which indicates the depth at which the Diamond Blade
(2E) is cutting. This saw also includes a Blade Depth
Stop (1J) which stops the cutting depth of the blade at a
specified depth.
Use of the Blade Depth Indicator (1K):
•
If the engine is running - Turn the Engine Start Switch
(1L) to the
“0” (OFF) position to STOP the engine.
•
Turn the Engine Start Switch (1L) to the “1” (ON)
position.
•
Lower the Diamond Blade (2E) by pushing the Toggle
Switch (1R) on the Control
Lever (1S) downward until
the Diamond Blade (2E) touches the surface to be cut.
•
Rotate the Blade Depth Indicator Knob (1K) to the zero
position. The blade cutting depth will now be indicated
on the Depth
Indicator (1K) when the blade is lowered
into the cutting surface.
Use of the Blade Depth Stop (1J) :
•
Lower the blade by pushing the Toggle Switch (1R) on
the Speed Control Lever (1S) downward until the
Diamond Blade (2E) is at the required depth [as
indicated on the Blade Depth Indicator (1K)].
•
Set the Blade Depth Stop (1J) by turning the knob
clockwise until tight. Now the maximum cutting depth
is set. If the saw is raised out of the cut surface for
any reason it can now be lowered to this specified
depth by lowering the blade into the cutting surface
with the Toggle Switch (1R) on the Control Lever (1S).
The saw WILL NOT lower to any depth greater
than the position set on the BLADE DEPTH
STOP (1J). Therefore, if a deeper cut is
required, the Depth Stop Knob MUST be
loosened, then SET to the new depth
required.
To Remove A SLIP-ON GUARD:
•
Using a Wrench, remove the rear retaining bolt.
•
Raise the Spade Safety Latch to unlatch and lift guard
off spade.
To Install A SLIP-ON GUARD:
•
Lower guard onto spade until latch engages.
•
Install bolt in rear of guard and tighten using Wrench.
(See Fig. 1, 2 and 3)
Always pay extreme care and attention to the
preparation of the machine before starting.
Remove all wrenches and tools from the floor
and the machine.
Always keep blade guard and transmission
guard in place.
•
Follow the operating instructions and warnings on top
of the saw cowl.
•
Close the Water Valve (1Z).
•
Mark the surface to be cut by drawing a line where the
cut is to be made.
•
Pull out Handle Bars (1B) to desired length and tighten
Knobs (1A).
•
Lower the Front Guide (3C). Align the Front Guide
(3C), Rear Guide (3D ) and Diamond Blade (2E) with
the line on the surface.
•
To start the saw with no water pressure, set the Water
Safety Switch (1O) to the “0” (OFF) position.
•
Set Speed Control Lever (1S) to the STOP (1V)
position. Saw will not start unless the Speed Control
Lever (1S) is in the
STOP (1V) position.
•
Start the engine using the Engine Start Switch (1L).
Follow the procedure in the engine manual.
•
Let the engine warm up for several minutes with the
Engine Throttle (1P) set at idle.
•
When ready, open the Water Valve (1Z).
•
Set Water Safety Switch to “1” (ON) .
Test for adequate water supply [2-1/2 to
5 gal/min (10 to 20 lit./min)]. Low water flow
will cause damage to diamond blades.
6 STARTING THE SAW