Target PRO 35 III DIESEL, Руководство по эксплуатации

Страница: 24 / 46

24
MANDA-
TORY
INDICATION
INFORMATION
INSTRUCTION
WARNING
PROHIBITION
Before starting up the machine, make sure you
read this entire manual and are familiar with
the operation of this machine.
The working area must be completely clear,
well lit and all safety hazards removed.
The operator must wear
protective clothing
appropriate to the work he
is doing.
MODEL 12" 14" 18" 20" 24"
35 III Diesel 3½ 4 ½ 6 ½ 7 ½ 9½
65 III Diesel 3 ½ 4 ½ 6 ½ 7 ½ 9 ½
Side Plunge --- --- 2" 3" n/a
Blade Size
MODEL 26" 30" 36" 42" 48"
35 III Diesel 10 ½ 12 ½ n/a n/a n/a
65 III Diesel 10 ½ 12 15 17 20
Side Plunge n/a n/a n/a n/a n/a
Blade Size
Any persons not involved in the work
should leave the area.
Use only blades marked with a maximum
operating speed greater than the blade shaft
speed.
(See Fig. 1 and 2)
Set The Handles To The Desired Length:
•
Loosen Knob (1A), pull the Handle Bar (1B) in or out to
desired length, then tighten the Knob (1A).
Moving The Saw With The Engine Off:
•
Turn Engine Start Switch (1L) to the “1” (RUN) position.
•
Raise the saw by pressing up on the Toggle Switch
(1R) on the Speed Control Lever (1S) until the
Diamond Blade (2E) (if installed) clears the pavement
surface.
•
Release the Parking Brake (if equipped) by pulling up
on Brake Knob (1N).
•
Pull up on the Neutral Knob (1W).
•
The saw can now be moved by standing behind it and
pushing [while holding the Handle Bars (1B)].
DO NOT attempt to push the saw while it is
parked on a grade (or hill). The saw operator
could lose control of the saw and cause
injury to himself or other person(s) in the area.
Moving The Saw With Engine On:
•
Turn Engine Start Switch (1L) to the “1” (RUN) position.
•
Raise the saw by pressing up on the Toggle Switch
(1R) on Speed Control Lever (1S) until
Diamond Blade (2E) (if installed) clears the pavement
surface.
•
Push down on the Neutral Knob (1W).
•
Push down on the Parking Brake Knob (1N)
(if equipped).
•
Set Water Safety Switch (1E) to “0” (OFF) .
•
Speed Control Lever (1S) must be in the STOP (1V)
position to start the saw. The engine WILL NOT start
unless the Speed Control Lever (1S) is in the
STOP (1V) position.
•
Diesel Models: Pull Throttle (1P) out halfway.
•
Turn the Engine Start Switch (1L) to the “2” (START)
position until the engine starts, then release the switch.
It will return to
“1” (RUN) position. If the engine does
not start, repeat these steps.
•
PUSH the Control Lever (1S) forward for Forward saw
movement, or to the rear for Reverse saw movement.
The further you push the lever the faster the speed.
2 MOVING THE MACHINE
These signs will give
advice for your safety
Before leaving our factory every machine is
thoroughly tested.
Follow our instructions strictly and your machine will
give you long service in normal operating conditions.
Use: Wet sawing of old and new concrete and asphalt.
Tools: Diamond blades — water cooled, Ø: 12",14", 18",
20", 24", 26", 30", 36", 42" and 48" with Arbor Ø - 1"
(For information, contact your Target supplier)
Depths of Cut (Maximum):
1 USE