Tar River SRB-870 страница 25 Скачать руководство пользователя

Страница: 25 / 70

Mini Round Baler SRB

870

Adjustments

Pick

up Suspension:

The pick

up suspension is supported by springs on both sides of the baler. Check the spring with the pick

up in

the working position. The correct length of the spring is

7/8”.

Be sure to check both springs. Adjustment to

the springs is made by loosening or tightening the nuts on the rod.

Twine Tension:

•

Check the tension on the twine tensioner springs prior to baling.

•

There has be sufficient tension on the twine so that it stays on the guides and is cut at the end of the baling
operation.

•

If the tension is too tight it will not properly feed through the guides possibly breaking the twine.

•

The springs are adjusted by tightening or loosening the nuts.

Pick

up Suspension

Twine Tensioner 1 (under RH side cover)

Twine Tensioner 2 (end of binding arm)

Содержание SRB-870







































































Результаты поиска

Содержание SRB-870

Отзывы:

Похожие инструкции для SRB-870

Бренды по названию

Популярные бренды

Tar River SRB-870, Руководство пользователя

Результаты поиска

Содержание SRB-870

Отзывы:

Похожие инструкции для SRB-870

Бренды по названию

Популярные бренды