Tar River SRB-870 страница 24 Скачать руководство пользователя

Страница: 24 / 70

Mini Round Baler SRB

870

Adjustments

Roller Chain continued:

Pick

up drive chain

Remove pick

up drive cover by removing the (3) threaded knobs.

Adjust the pick

up drive chain tension by changing the position of the tension pulley.

Chain deflection should be set at approximately

1/8”.

Pick

up drive slip clutch

The pick

up drive comes standard with a slip clutch to prevent damage to the baler. If the pick

up drive hits an

object and can not turn, the clutch will slip to prevent damage to the baler.

The correct setting is approximately

1”.

Adjust tension if under normal circumstances there is excessive slip-

ping. If slipping continues after adjustment, the friction discs should be changed.

Tension Pulley

Threaded Knobs

Slip Clutch Springs

Содержание SRB-870







































































Результаты поиска

Содержание SRB-870

Отзывы:

Похожие инструкции для SRB-870

Бренды по названию

Популярные бренды

Tar River SRB-870, Руководство пользователя

Результаты поиска

Содержание SRB-870

Отзывы:

Похожие инструкции для SRB-870

Бренды по названию

Популярные бренды