Tar River SRB-870 Скачать руководство пользователя

Страница: 13 / 70

Mini Round Baler SRB

870

Assembly

Attaching wheels:

•

Remove the wheels from the baling chamber, unlock the flow control valve and close the rear door.

Cau-

tion:

Before closing the rear door make sure no one is standing near the rear of the baler.

•

Using the tractor 3

point, lift the baler high enough to insert wheels into baler frame.

•

Insert the shaft of one wheel assembly on to the baler frame as shown below.

•

There are two indents on the shaft. Line up the indent with the bolt hole in baler frame. Thread the bolt un-
til it locks into the indent on the shaft. Tighten the bolt and lock nut. Repeat for the other wheel assembly.

•

The wheels can be set in two positions. Choose the position best suited for your application.

RH Wheel Assembly

LH Wheel Assembly

Содержание SRB-870







































































Результаты поиска

Содержание SRB-870

Отзывы:

Похожие инструкции для SRB-870

Бренды по названию

Популярные бренды

Tar River SRB-870, Руководство пользователя

Результаты поиска

Содержание SRB-870

Отзывы:

Похожие инструкции для SRB-870

Бренды по названию

Популярные бренды