background image

Children should not be allowed on the product.

Clear the area of small children and bystanders before moving the feeder.

If using a towing unit, securely attach feeder by 

using a hardened 3/4” pin, a metal retainer, and safety

chains if required.  Shift towing unit to a lower gear before going down steep downgrades, thus using
the engine as a retarding force.  Keep towing vehicle in gear at all times.  Slow down for corners and
rough terrain.

Make sure you are in compliance with all local and state regulations regarding transporting equipment

on public roads and highways.  Lights and slow moving signs must be clean and visible by overtaking or
oncoming traffic when feeder is transported.

Beware of bystanders, 

particularly children

!  Always look around to make sure that it is safe to start

the engine of the towing vehicle or move the unit.  This is particularly important with higher noise levels
and quiet cabs, as you may not hear people shouting.

NO PASSENGERS ALLOWED

 - Do not carry passengers anywhere on, or in, the tractor or equipment,

except as required for operation.

Keep hands and clothing clear of moving parts.

Do not clean, lubricate or adjust your equipment while it is moving.

When halting operation, even periodically, set the tractor or towing vehicle brakes, disengage the PTO,

shut off the engine and 

remove the ignition key

.

Be especially observant of the operating area and terrain - watch for holes, rocks or other hidden

hazards.  Always inspect the area prior to operation.

DO NOT

 operate near the edge of drop-offs or banks.

DO NOT

 operate on steep slopes as overturn may result.

Operate up and down (not across) intermediate slopes.  Avoid sudden starts and stops.

DURING OPERATION 

Содержание SRB-870













































Отзывы: