background image

230905-36 

TC42_B2      page 23

LIGHTING INSTRUCTIONS - Millivolt Valve 

TO TURN OFF GAS TO APPLIANCE

1.  Set wall thermostat to lowest setting, if applicable.

LIGHTING INSTRUCTIONS

1.  STOP! Read the safety information above on this label.
2.  Set wall thermostat to lowest setting, if applicable.
3.  Turn off all electric power to the appliance, if applicable.
4.  This appliance is equipped with an ignition device which 

automatically lights the pilot. Do not try to light the pilot by 
hand.

5.  Partially depress and turn gas control 

knob clockwise 

 past "Pilot" to "Off" 

position.

Note: Knob cannot be turned from "Pilot" to 

"Off" unless knob is pushed in slightly. 
Do not force.

6 Allow 

suffi cient length of time (minimum 5 minutes) for any 

gas in the combustion chamber to escape. If you still smell 
gas, STOP! Follow "B" in the safety information above on 
this label. If you don't smell gas, go to the next step.

7.  Turn gas control knob back to "Pilot" position.

WARNING: If you do not follow these instructions 

exactly, a fi re or explosion may result causing 
property damage, personal injury or loss of life.

A.  This appliance is equipped with an ignition device which auto-

matically lights the pilot. Do not try to light the pilot by hand.

B.  BEFORE LIGHTING smell all around the appliance area for gas. 

Be sure to smell next to the fl oor because some gas is heavier 
than air and will settle on the fl oor.

 

WHAT TO DO IF YOU SMELL GAS:

 

- Do not try to light any appliance.

 

- Do not touch any electric switch; do not use any phone in your 

FOR YOUR SAFETY READ BEFORE LIGHTING

2.  Turn off all electric power to the appliance if service is to be 

performed.

3.  Push in gas control knob slightly and turn clockwise 

 to 

"Off". Do not force.

8.  Depress gas control knob fully and hold to ignite pilot. Once 

the pilot ignites, continue depressing knob for approxi-
mately 5 seconds, or until pilot fl ame indicator is in the RED 
zone. If pilot does not stay lit, repeat steps 5 through 8, 
allowing a longer period before releasing gas control dial.

 

- If gas control knob does not pop up when released, stop 
and immediately call your service technician or gas sup-
plier.

 

- If the pilot will not stay lit after several tries, turn the gas 
control knob to "Off" and call your service technician or gas 
supplier.

9.  Turn gas control knob counter-clockwise 

 to "On" posi-

tion.

10. Turn HI-LO burner control knob to desired setting.
11. Turn on the burner switch and close control door.
12. Turn on all electric power to the appliance, if applicable.
13. Set thermostat to desired setting, if applicable.
 Note: 

Suffi cient time must be allowed for air to escape from 

lines if the unit is being lit for the fi rst time.

building.

 

- Immediately call your gas supplier from a neighbour's phone. 
Follow the gas supplier's instructions.

 

- If you cannot reach your gas supplier, call the fi re  depart-
ment.

C. Use only your hand to push in or turn the gas control knob. 

Never use tools. If the knob will not push in or turn by hand, 
don't try to repair it, call a qualifi ed service technician. Force or 
attempted repair may result in a fi re or explosion.

D. Do not use this appliance if any part has been under water. 

Immediately call a qualifi ed service technician to inspect the 
appliance & to replace any part of the control system & any gas 
control which has been under water. 

FIRST FIRE

When lit for the fi rst time, the fi replace will emit a slight odour 
for a couple of hours. This is due to the curing of paints, seal-
ants and lubricants used in the manufacturing process. This 
condition is temporary. Open doors and windows to ventilate 
area. Smoke and fumes caused by the curing process may 
cause discomfort to some individuals.
It is normal for fi replaces fabricated of steel to give off some 
expansion and/or contraction noises during the start up or 
cool down cycle. Similar noises are found with your furnace 
heat exchanger or cook stove oven.

OPERATING

The Town and Country Fireplace comes equipped with either 
a manual (millivolt) combination gas valve or an electronic 
gas valve. An optional wall switch or thermostat (Canada 
only) may be installed to operate the burner automatically on 
both types of valve.

Manual Valve:  

Once a pilot light has been established, 

and the gas valve knob turned to the "O

N

" position (Manual 

Valve) or simply switched on with the "Burner" switch, the unit 
may be operated in one of two ways; manually adjusting the 
fl ame and/or turning the unit on and off automatically with a 
wall thermostat.

Содержание TC42 B Series





































Отзывы: